Investigation of the effect of water to cementitious materials ratio and silica fume on the fracture behavior and brittleness of high strength concrete by size effect method

Document Type : Original Research

Authors
S. M. Mousavi 1
R. Madandoust 2
M. M. Ranjbar 2
1 PhD student of the University of Guilan
2 Associated professor of Faculty of engineering of the University of Guilan
Abstract
In structural engineering, concrete is known as a material with brittle behavior that the tensile strength of which is negligible compared to its compressive strength and show low resistance to crack propagation. Moreover, the concrete can be considered as a quasi-brittle material, which is due to the type of behavior related to the crack propagation and is also existed around the crack tip of fracture process zone (FPZ) that involves a set of microcracks. From the perspective of structural behavior, the size effect of the structure is one of the most important concepts provided by the fracture mechanics; therefore, it is important to provide an equation between concrete fracture properties such as fracture toughness (KIC) and fracture energy (Gf) and its correlation with the size effect mechanism. The fracture energy is one of the most important characteristics for analysis of fracture behavior in concrete, evidenced to be a concrete property, showing its strength to cracking and fracture toughness. Given that the fracture energy (Gf) is sufficient to calculate the fracture behavior evaluation for the brittle materials in range of linear fracture mechanics, for the quasi-brittle materials such as concrete, this is not a sufficient parameter due to the presence of microcracks in the fracture process zone, and the length of fracture process zone (Cf) is one of the important properties of fracture in the unlimited-size structures. For determining the fracture parameters of concrete, various methods have been proposed. One of the most important methods that is presented by Bazant is the size effect method (SEM). The use of high strength concretes is increasing due to the expansion of the construction technology of these concretes. This research studies and analyzes the fracture behavior of high strength concrete (HSC) with various amounts of silica fume, along with a change in water to cement (w/c) ratio with SEM. In this experimental study, a total of 10 mixing designs have been tested. To investigate the effects of different w/c ratios in the range of HSC and the effect of silica fume, four w/c ratios of 0.24, 0.3, 0.35 and 0.4 Examined and in two w/c ratios of 0.24 and 0.35 a mix design for plain concrete without silica fume and three mix designs prepare with silica fume content of 5%, 10% and 15% by weight of cement. To determine the fracture characteristics of concrete, a total of 120 beams were tested. The results show that by decreasing the w/c ratio from 0.35 in the range of HSC, the value of initial fracture energy (Gf), the effective length of fracture processing zone (Cf) and the critical crack tip opening displacement (CTODc) has decreased and on the other hand the brittleness number (β) has increased. Also, by increasing the amount of silica fume in the w/c ratios of 0.35 and 0.24, the fracture energy, the length of the fracture processing zone, the fracture toughness (KIC), the critical crack tip opening displacement has reduced, and the brittleness number has increased. The results show that by using the fracture parameters obtained from the SEM, the maximum load on the high strength concrete specimen can be predicted correctly.

Keywords

Subjects

1- Tasdemir, C., Tasdemir, M.A., Lydon, F.D. and Barr, B.I., 1996. Effects of silica fume and aggregate size on the brittleness of concrete. Cement and Concrete Research, 26(1), pp.63-68.
2- Mitsui, K., Li, Z., Lange, D.A. and Shah, S.P., 1994. Relationship between microstructure and mechanical properties of paste-aggregate interface. Materials Journal, 91(1), pp.30-39.
3- Husem, M., 2003. The effects of bond strengths between lightweight and ordinary aggregate-mortar, aggregate-cement paste on the mechanical properties of concrete. Materials Science and Engineering: A, 363(1-2), pp.152-158.
4- Akçaoğlu, T., Tokyay, M. and Çelik, T., 2005. Assessing the ITZ microcracking via scanning electron microscope and its effect on the failure behavior of concrete. Cement and Concrete Research, 35(2), pp.358-363.
5- Bentur, A., 1990. Microstructure, interfacial effects and micromechanics of cementitious composites, Advances in Cementitious Materials. Am. Ceram. Soc., 16, pp.523-550.
6- Merchant, I.J., Macphee, D.E., Chandler, H.W. and Henderson, R.J., 2001. Toughening cement-based materials through the control of interfacial bonding. Cement and concrete research, 31(12), pp.1873-1880.
7- Prokopski, G. and Langier, B., 2000. Effect of water/cement ratio and silica fume addition on the fracture toughness and morphology of fractured surfaces of gravel concretes. Cement and Concrete Research, 30(9), pp.1427-1433.
8- Mindess, S., Young, J.F. and Darwin, D., 1981. Concrete (pp. 339-344). Englewood Cliffs, NJ: Prentice-Hall.
9- Jo, B.W. and Tae, G.H., 2001. Experimental study on fracture energy of low-heat concrete by three-point bend tets. Russian journal of nondestructive testing, 37(12), pp.907-915.
10- Carpinteri, A. and Brighenti, R., 2010. Fracture behaviour of plain and fiber-reinforced concrete with different water content under mixed mode loading. Materials & Design, 31(4), pp.2032-2042.
11- Köksal, F., Altun, F., Yiğit, İ. and Şahin, Y., 2008. Combined effect of silica fume and steel fiber on the mechanical properties of high strength concretes. Construction and building materials, 22(8), pp.1874-1880.
12- Aïtcin, P.C., 2014. Binders for durable and sustainable concrete. CRC Press.
13-Guinea, G.V., El-Sayed, K., Rocco, C.G., Elices, M. and Planas, J., 2002. The effect of the bond between the matrix and the aggregates on the cracking mechanism and fracture parameters of concrete. Cement and concrete research, 32(12), pp.1961-1970.
14- Bharatkumar, B.H., Raghuprasad, B.K., Ramachandramurthy, D.S., Narayanan, R. and Gopalakrishnan, S., 2005. Effect of fly ash and slag on the fracture characteristics of high performance concrete. Materials and Structures, 38(1), p.63.
15- Recommendation, R.D., 1990. Size-effect method for determining fracture energy and process zone size of concrete. Materials and Stuctures, (23), pp.461-465.
16- Bažant, Z. P., &Kazemi, M. T. (1990). Size effect in fracture of ceramics and its use to determine fracture energy and effective process zone length. Journal of the American Ceramic Society, 73(7), 1841-1853.
17- Bazant, Z. P., &Kazemi, M. T. (1990). Determination of fracture energy, process zone longth and brittleness number from size effect, with application to rock and conerete. International Journal of fracture, 44(2), 111-131.
18- ASTM C 33: Standard specification for concrete aggregates. American standards for testing and materials; 2003.
19-BS EN 12390. part3: Testing hardened concrete. Method of determination of compressive strength of concrete cubes. British standards institution; 2000.
20- ASTM C 469: Standard test method for static modulus of elasticity and poisson's ratio of concrete in compression.American Standards for Testing and Materials; 2002.
21- ASTM C 496: Standard test method for splitting tensile strength of cylindrical concrete specimens.American Standards for Testing and Materials; 2011.
22- Raisi, E.M., Amiri, J.V. and Davoodi, M.R., 2018. Influence of rice husk ash on the fracture characteristics and brittleness of self-compacting concrete. Engineering Fracture Mechanics, 199, pp.595-608.
Modares Civil Engineering journal
Volume 19, Issue 4
November and December 2019
Pages 201-214