مقاوم‌سازی برشی تیرهای بتن مسلح به روش نصب نزدیک سطح با استفاده از میله‌های ساخته‌شده ازالیاف کربن

نویسندگان
میثم جلالی 1
فرشید جندقی علایی 2
محمدکاظم شربتدار 3
1 دانشگاه دامغان
2 دانشگاه صنعتی شاهرود
3 دانشگاه سمنان
چکیده
This experimental study is intended to evaluate the effectiveness of a Near Surface Mounted (NSM) technique using bars made of carbon fabrics (BMCF) for strengthening of RC beams. When the amount of NSM reinforcement in strengthening of RC beams is low, the failure is likely to be due to debonding of individual reinforcing rod and in this case improved bond properties as well as proper anchoring of the BMCF rods are likely to delay the failure of the beam. BMCF provide a larger perimeter to cross sectional area ratio with respect to conventional rods for the same amount of fibre used, providing potentially higher bond strength. In addition, the circular shape of BMCF is not only convenient for production but also suitable for NSM strengthening as noted by previous researchers. Another key advantage of introducing the BMCF is that it allows the incorporation of a different anchor system that can be used to improve the performance of NSM BMCF reinforcement for strengthening of RC beams in applications with low strengthening reinforcement percentage. A distinguished benefit of the proposed anchor system is that it only requires the access to the beam sides for installation. This means that the proposed anchorage system can be conveniently applied to beams whose top and/or bottom face is inaccessible. A set of deficient beam specimens were designed. All specimens had the same internal reinforcement arrangements. They were 300 mm wide, 350 mm high and 2050 mm long. One half of each beam was designed to be weak in load bearing as the test span while the other half was designed as the strong span. Only the test span was strengthened in with NSM BMCF. The amount of steel reinforcement in the two sides was designed to ensure that shear failure would occur in the test span. All beams were simply supported at the ends and tested under a concentrated monotonic load applied at the mid-span. Test results presented in this paper have confirmed that the use of BMCF is an effective technique for improving the shear capacity of RC beams. The increase in the shear capacity was between 18 to 55% for beams strengthened with BMCF, compared with the reference beam. The load–deflection response of beams is presented. The capacity of specimens for energy absorption are also presented and discussed in this paper. In order to predict the contribution of NSM-BMCF strengthening method, an analytical study is presented in this paper. The analytical procedure is evaluated by experimental findings. It is concluded that the analytical formulation can reasonably estimates the contribution of NSM-BMCF strengthening reinforcement and as a safe design point of view; it is advisable for engineering application aims.

کلیدواژه‌ها

عنوان مقاله English

Strengthening of Reinforced Concrete Structures Using BMCF Bars

نویسندگان English

M. Jalali 1
F. Jandaghi Alaee2 Jandaghi Alaee 2
M. K. Sharbatdar 3
1 Damghan University
2 Shahrood University of Technology
3 Semnan University
چکیده English

چکیده-مطالعه آزمایشگاهی انجام شده، تأثیر مقاوم سازی برشی تیرهای بتن مسلح به کمک روش نصب نزدیک سطح با استفاده از میله های ساخته شده از صفحات الیاف کربن را ارزیابی می کند. برای ایجاد تأخیر در شروع جداشدگی میله از تیر، مهار انتهایی جدیدی برای آن ها پیشنهاد شده که آزمایش می شود. در این مقاله، نتایج آزمایش های انجام شده روی شش عدد تیر بتن مسلح دوسر ساده با مقطع مستطیل شکل که در برش، مقاوم سازی شده است، ارائه می شود. پاسخ نیرو- تغییرمکان همه ی نمونه ها و تغییرات کرنش در قسمت های مختلف ارائه خواهد شد. همچنین کارکرد و مدهای گسیختگی تیرها بررسی خواهد شد. نتایج آزمایش ها بیانگر از کارامدی میله ها و مهارهای پیشنهادی بوده است؛ به گونه ای که افزایش ظرفیت باربری نمونه های مقاوم سازی شده روش پیشنهادی، 25 تا 48 درصد نمونه مرجع به دست آمده است و در نتیجه استفاده از مهارهای انتهایی پیشنهادی، انرژی جذب شده به وسیله ی نمونه ها، افزایش چشم گیری پیدا کرده است. در انتها، مدل تحلیلی Rizzo and De Lorenzis برای برآورد مشارکت سامانه مقاوم سازی این پژوهش ارائه شده است که در مقایسه با نتایج آزمایشگاهی، تخمین قابل قبولی به دست می دهد.

کلیدواژه‌ها English

BMCF bar
Strengthening
Structural Behaviour
analytical model
energy absorption
9- مراجع
[1]  American Concrete Institute. ACI Committee 440. “Guide for the design and construction of externally bonded FRP system for strengthening concrete structures”. Farmington Hills, MI: ACI 440.2R-08; 2008.
[2]  Teng J.G., Chen J.F., Smith S.T., Lam L. “Behaviour and strength of FRP-strengthened RC structures: a state-of-the-art review”. Proceedings of the Institution of Civil Engineers– Structures and Buildings 2003;156(SB1); 51-62.
[3]  Hollaway L.C., Teng J.G. “Strengthening and rehabilitation of civil infrastructures using fibre-reinforced polymer (FRP) composites”. Cambridge, UK:Woodhead Publishing Limited; 2008.
[4]  El-GhandourA.A.“Experimental and analytical investigation of CFRP flexural and shear strengthening efficiencies of RC beams”. Construction and Building Materials, 2011;25(3):1419-29.
[5]  Chen J.F., Teng J.G. “Shear capacity of FRP strengthened RC beams: fibre reinforced polymer rupture”. Journal of Structural Engineering ASCE, 2003;129(5):615-25.
[6]  Chen J.F., Teng J.G. “Shear capacity of FRP strengthened RC beams: FRP debonding”. Construction and Building Materials, 2003; 17 (1) :27-41.
[7]  Teng J.G., Lam L., Chen J.F. “Shear strengthening of RC beams using FRP composites”. Progress in Structural Engineering Material, 2004;6:173-84
[8]  Adhikary B.B, Mutsuyoshi H., Sano M. “Shear strengthening of reinforced concrete beams using steel plates bonded on beam web: experiments and analysis”. Construction and Building Materials, 2000;14(5):237–44.
[9]  Teng JG, Chen JF, Smith ST, Lam L. “FRP-strengthened RC structures”. Chichester, UK: John Wiley and Sons Inc;2002.
[10]   Chen J.F. Teng J.G. “Anchorage strength models for FRP and steel plates bonded to concrete”. Journal of Structural Engineering ASCE, 2001;127(7):784-91.
[11]   Cao S.Y., Chen J.F., Teng J.G., Hao Z., Chen J. “Debonding in RC beams shear strengthened with complete FRP wraps”. Journal of Composites for Construction ASCE, 2005;9(5):417-28.
[12]   De Lorenzis L., Teng J.G. “Near-surface mounted FRP reinforcement: an emerging technique for strengthening structures”. Composites Part B:Engineering,2007;38:119–43.
[13]   DeLorenzisL., Nanni A. “Characterization of FRP rods as near-surface mounted reinforcement”. Journal of Composites for Construction, 2001;5(2):114-21.
[14]   Rizzo A., De Lorenzis L. “Behaviour and capacity of RC beams strengthened in shear with NSM FRP reinforcement”. Construction and Building Materials, 2009;23(4):1555–67.
[15]   Dias S.J.E., Barros J.A.O. “Shear strengthening of T cross section reinforced concrete beams by near surface mounted technique”. Journal of Composites for Construction ASCE, 2008;12(3):300-11.
[16]   Dias S.J.E., Barros JAO. “Performance of reinforced concrete T beams strengthened in shear with NSM CFRP laminates”. Engineering Structures, 2010;32(2):373-84.
 
 
 
 
 
 
 
 
 
 
 
 
[17]   Barros J.A.O, Dias S.J.E. “Near surface mounted CFRP laminates for shear strengthening of concrete beams”. Cement and Concrete Composites, 2006;28(3):276–92.
[18]   Rahal K.N, Rumaih H.A. “Tests on reinforced concrete beams strengthened in shear using near surface mounted CFRP and steel bars”. Engineering Structures, 2011;33(1):53-62.
[19]   Anwarul-islam A.K.M. “Effective methods of using CFRP bars in shear strengthening of concrete girders”. Engineering Structures, 2009;31(3):709-14.
[20]   AL-Mhammoud F., Castel A., François R., Tourneur C. “Strengthening of RC members with near-surface mounted CFRP rods”. Composite Structures, 2009;91(2):138-47.
[21]   Sharbatdar M.K. “Concrete columns and beams reinforced with FRP bars and grids under monotonic and reversed cyclic loading”. PhD Thesis, University of Ottawa, Canada 2003.
[22]   Rizzo A, DeLorenzis L. “Modeling of debonding failure for RC beams strengthened in shear with NSM FRP reinforcement”. Construction and Building Materials, 2009; 23(4):1568–77.
[23] جلالی میثم، شربتدار محمدکاظم، جندقی علایی فرشید. "ساخت و ارائه مهار انتهایی برای میله های پلیمری مسلح به الیاف به منظور مقاوم سازی برشی تیرهای بتن مسلح". سازمان ثبت اسناد و املاک کشور، اداره ثبت اختراعات. 73918، 1390.
مهندسی عمران مدرس
دوره 13، شماره 1
فروردین و اردیبهشت 1392
صفحه 1-14