تخمین مقاومت نهایی تیرهای عمیق دوسر ساده تحت بار متمرکز با استفاده از نظریه روش خرپایی

نوع مقاله : پژوهشی اصیل (کامل)

نویسندگان
دانشگاه تربیت مدرس
10.48311/mcej.2025.99125.0
چکیده
تیرهای عمیق به دلیل داشتن هندسه‌ی خاص نسبت به تیرهای معمولی توزیع کرنش در مقطع این تیرها به صورت خطی نبوده و عموما دارای رفتار برشی می‌باشند و توزیع تنش در این تیرها برخلاف تیرهای معمولی که دارای توزیع خطی هستند، به شکل غیرخطی خواهد بود. بر همین اساس تیرهای عمیق نیاز به روش خاصی برای طراحی نسبت به تیرهای معمولی دارند. روش خرپایی یکی از روش‌هایی است که اخیرا برای تیرهای عمیق پیشنهاد شده است. بر اساس مدل خرپایی برخی نواحی در سازه‌های بتنی که دارای وضعیت آشفته در توزیع تنش دارند را با تعیین مسیرانتقال نیرو‌ها در المان بتنی به یک خرپای ساده تبدیل کرد. در این مقاله ضمن بررسی روش‌های موجود در آیین‌نامه‌ها و نیز رابطه خرپایی توسعه یافته توسط نویسنده و همکاران و همچنین روابط پیشنهادی سایر محققین، یک روش خرپایی اصلاح و پیشنهاد شده. نتایج نشان می‌دهند که آیین‌نامه‌ها در برآورد ظرفیت برشی تیرهای عمیق دوسر ساده تحت بار متمرکز محافظه‌کارانه عمل کرده به گونه‌ای که این محافظه‌کاری در آیین‌نامه بتن آمریکا حدود ۱۵٪ می‌باشد. رابطه خرپایی پیشنهاد شده قبلی با ۳۸۷ نمونه آزمایشگاهی تیر عمیق دو سر ساده با بارگذاری متمرکز بررسی و خطاهای رابطه پیشنهادی بهبود داده شد. با بازنویسی و اصلاح رابطه فوق به کمک رگرسیون غیرخطی با مطالعه بر روی ۳۸۷ نمونه آزمایشگاهی، نتایج در عدم حضور میلگرد برشی عمودی جان از ۳۲٪ غیر ایمن به ۵/۲٪ کاهش پیدا کرد. همچنین خطای محاسباتی در تیر‌های عمیق با دهانه برشی به ارتفاع موثر کمتر از ۵/۰ و ما بین ۵/۰ تا ۱ به ترتیب از حدود ۲۴٪ و ۱۷٪ در جهت غیر ایمن به ۷٪ و ۲٪ محافظه‌کارانه بهبود یافت.
کلیدواژه‌ها
موضوعات

عنوان مقاله English

Estimation of the ultimate strength of simply support deep beams under concentrated load using the theory of the STM

نویسندگان English

Abolfazl Arabzadeh
farshad shahi
University
چکیده English

Deep beams, due to their special geometry, are not linear in their cross-section and generally have shear behavior, and the stress distribution in these beams is nonlinear, unlike conventional beams that have a linear distribution. Accordingly, deep beams require a special design method compared to conventional beams. The truss method is one of the methods that has recently been proposed for deep beams. Based on the truss model, some areas in concrete structures that have a chaotic state in stress distribution were converted into a simple truss by determining the direction of force transfer in the concrete element. In this paper, while examining the methods available in the codes and the truss relationship developed by the author and colleagues as well as the relationships proposed by other researchers, a modified truss method was proposed. The results show that the codes have acted conservatively in estimating the shear capacity of simple double-ended deep beams under concentrated load, such that this conservatism in the American Concrete Code is about 15%. The previously proposed truss relation was investigated with 387 laboratory specimens of simple double-ended deep beams with concentrated loading and the errors of the proposed relation were improved. By rewriting and modifying the above relation using nonlinear regression with a study on 387 laboratory specimens, the results in the absence of vertical shear reinforcement of the web were reduced from 32% unsafe to 2.5%. Also, the calculation error in deep beams with shear spans of effective height less than 0.5 and between 0.5 and 1 was improved from about 24% and 17% in the unsafe direction to 7% and 2% conservative, respectively.

کلیدواژه‌ها English

Deep beam
shear capacity
bending failure
local failure
Strut and Tie method

مقالات آماده انتشار، اصلاح شده برای چاپ
انتشار آنلاین از 27 آبان 1405