fa
jalali
1392
9
1
gregorian
2013
12
1
13
5
online
1
fulltext
fa
بررسی تجربی پارامترهای ریسک آتشسوزی برای تعدادی مصالح ساختمانی پلیمری و ارائه یک روش جدید طبقهبندی
An experimental fire risk assesment of some polymeric building materials and proposing a new fire risk classification method
رفتار ده مصالح ساختمانی رایج و جدید پلیمری در برابر آتش به وسیله گرماسنج مخروطی در تابش kW/m2 50 آزمایش شد. پارامترهای حرارتی آتش ناشی از سوختن مواد، با هدف تحلیل ریسک آنها در گسترش آتشسوزی ارائه و بحث شده است. ریسک مواد در آتشسوزی به وسیله روش های ارائه شده توسط محققین مختلف و نرمافزار Conetools بررسی و بحث شد. اکثر مواد بررسی شده، رفتار خطرناکی در برابر آتش داشتند. خصوصاً نمونه های اپوکسی، MDF، HDF و پلی کربنات بسیار خطرناک نشان دادند. نتایج نشان داد که پارامترهای زمان افروزش، شدت رهایش گرما و کل رهایش گرما مهمترین مشخصات آتش مواد برای تعیین ریسک آنها در گسترش آتشسوزی هستند. زمان افروزش بر روی زمان وقوع گُر گرفتگی در اتاق و سرعت پیشروی سطحی شعله بر روی نازک کاری ها تأثیر مهمی دارد و نادیده گرفتن آن میتواند به پیشبینی اشتباه ریسک مواد در گسترش آتشسوزی منجر شود. یک روش جدید برای طبقه بندی ریسک مواد در برابر آتش تهیه شد که می تواند در مقررات ملی ساختمان برای ارزیابی خواص مواد در برابر آتش مورد استفاده قرار گیرد.
Fire is a potential threat for all buildings. It can produce life and property losses and even ending to fail of the building. Therefore; fire safety is one of the most important requirements in design and construction of buildings. In other side, the use of polymeric building materials has been considerably developed in construction industry in recent years. Most of these materials are highly flammable and can seriously contribute to growth of probable fires in buildings. Hence; it is needed to evaluate the fire behavior of these materials and restrict their application in buildings, if they show a high contribution to fire growth. In this research, the fire behaviors of 10 polymeric building materials were studied with cone calorimeter at 50 kW/m2. The reaction to fire properties of the burned specimens were presented and discussed. The correlations between the acquired fire parameters were evaluated. This could assist in analysis of the fire growth risk of the specimens. The fire risk of the tested materials was evaluated with different methods, including methods proposed by Richardson, Östman and Nussbaum, Petrella and the software program conetools. The results were compared and it was revealed that there were some disagreements. The reasons of these disagreements were discussed. The most tested materials showed a dangerous behavior against the fire. They released considerable amount of heat and high peaks of heat release rate. Especially epoxy, MDF, HDF and polycarbonate samples showed high potentials for contribution in fire growth. The results showed that the time to ignition, heat release rate and total heat release are the least fire parameters that should be considered in any fire risk classification method. The time to ignition has an important influence on flame spread on the linings and on time to flashover in the room of origin of fire. Disregarding the time to ignition in any classification method, as it can be seen in that proposed by Richardson, could result in incorrect predictions of fire risk of materials. A new classification method for reaction to fir of materials is proposed in this paper. In this method, the combustibility of materials is evaluated when they are exposed to a radiant heat flux 50 kW/m2 for 15 minutes. The method is an improved version of the method given by Richardson. The peak of heat release rate, total heat release and propensity to flashover (i.e. the ratio of the peak rate of heat release to the time to ignition) are used for classification of fire risk of materials in this method. It is fairly simple and does not need fire tests in medium or large scales (like SBI or room corner tests). It is proposed for use in chapter three of building code of Iran, which is allocated to fire safety of buildings.
conetools,Fire safety,fire risk classification,building code,cone calorimeter,conetools
ایمنی در برابر آتش,طبقهبندی ریسک آتشسوزی,مقررات ساختمانی,گرماسنج مخروطی
1
1
http://mcej.modares.ac.ir/browse.php?a_code=A-16-1000-9194&slc_lang=fa&sid=16
2012/04/29
1391/2/10
2013/05/16
1392/2/26
saeid
bakhtiary
سعید
بختیاری
00319475328460049595
00319475328460049595
Yes
مرکز تحقیقات ساختمان و مسکن
لیلا
تقی اکبری
00319475328460049596
00319475328460049596
No
مرکز تحقیقات ساختمان و مسکن
مسعود
جمالی آشتیانی
00319475328460047456
00319475328460047456
No
مرکز تحقیقات ساختمان و مسکن
fa
ارائه مدلی برای افزایش فاصله و کاهش ابعاد سختکنندههای تیرپیوند قوطی شکل قابهای مهاربندی شده برونمحور
A Model for Increasing the Distances and Decreasing the Dimensions of Stiffeners for Tubular Link Beams in Eccentrically Braced Frames
- تیرهای پیوند با مقطع عرضی قوطی در قابهای مهاربندی شده برونمحور به دلیل دارا بودن پایداری پیچشی ذاتی برخلاف تیرهای پیوند I شکل، نیاز به مهارجانبی ندارند و کمانش پیچشی جانبی در آنها کمتر رخ میدهند. با این وجود مقاطع عرضی I شکل، به دلیل حاکم بودن شرایط مرزی گیردار در تمام وجوه ورق جان نسبت به ورق جان مقاطع عرضی قوطی که داری شرایط مرزی ساده هستند، دارای مزیت میباشند. در این تحقیق، تیرهای پیوند با مقاطع عرضی قوطی و I شکل مختلف در محدوده غیرالاستیک مورد بررسی قرار گرفتهاند و سعی شده است که با تغییر در نحوه آرایش سختکنندههای تیرپیوند قوطی شکل، افزایش فواصل و کاهش ابعاد آنها حاصل شود. برای انجام مطالعات عددی از نرمافزار اجزاء محدود و پروتکل بارگذاری AISC 2005 استفاده شده است. بررسی عددی مدلهای مختلف تیرپیوند نشان میدهد که چنانچه تیرهای پیوند I شکل و قوطی دارای مشخصات هندسی یکسان باشند تیرهای پیوند I شکل به دلیل عملکرد بهتر ورق جان، از ظرفیت دوران بالاتری برخوردار هستند که این افزایش ظرفیت در حدود دو برابر میباشد. همچنین بررسی نتایج نشان میدهد که آرایش جدید سختکنندههای تیرپیوند قوطی، باعث افزایش فواصل آنها در حدود 30% و کاهش ابعاد آنها در حدود 15% شده به گونهای که بر ظرفیت زاویه دوران نیز تأثیر نامطلوبی نمیگذارد. همچنین بررسیها نشان میدهند که ابعاد سختکنندهها در صورت ارضاء مساحت و مماناینرسی مورد نیاز تأثیری روی ظرفیت زاویه دوران ندارند.
Eccentrically braced frames (EBF) by covering the advantages of moment-resisting frames (MRF) and concentrically braced frames (CBF) have been used as seismic load resisting systems in buildings for more than two decades. In eccentrically braced frames (EBFs), the link beams transmit bracing forces through themselves into the columns and other bracings and, in the end, create dominant forces in the bracings. Link beams, similar to ductile fuses, in addition to avoiding bracing buckling, attract earthquake energies. In EBF system, failure and yielding should happen in the link beams, and other members of the structure must remain in elastic behaviour. On the other hand, link beams prevent transmitting of more forces to the other members by yielding, therefore, these link beams are so important. Typically, the link beams, which are relied upon for energy dissipation through inelastic deformation, have had a wide-flange or I-shaped cross-section that requires lateral bracing to prevent lateral torsional buckling. This has limited the use of eccentrically braced frames in bridge piers and towers, as lateral bracing is difficult to provide in those situations. Tubular cross-sections of link beams have substantial torsional stability, making them less susceptible to lateral torsional buckling than I-shaped cross-sections in eccentrically braced frames, and may thus not require lateral bracing.Web of I-shaped cross-sections because of having clamped boundary conditions in its four sides than web of tubular cross-sections that have simply supported boundary conditions in its four sides, having advantage. Web buckling of link beams in eccentrically braced frames cause rapid strength and stiffness degradation, and this significantly impedes the energy dissipation capabilities of the system. Web stiffeners can be used to delay web buckling beyond a certain rotation level.Stiffener spacing of link beam is of important causes for the delay of web buckling. Stiffener spacing is based on the boundary condition of web that is between the flanges and the stiffeners. In this study, link beams with different tubular and I-shaped cross-sections in non-elastic limits are investigated and has been tried by changing link beams stiffeners array cause increasing the distances and decreasing the dimensions of them. For this purpose nonlinear finite element software and AISC-2005, loading protocol are used.The numerical result ofdifferent link beams models indicate that tubular and I-shaped cross-sections if having same geometric profile, I-shaped cross-sections have higher rotation capacity because ofbetter performance of their web, this increasing is approximatelly twice. So study of results indicate that new arraying of stiffeners of tubular link beam inceases the distances of them approximatelly 30% and decreasing the dimensions of them approximatelly 15% anddoesn’t have any bad effect on rotation angle capacity of them. An investigation of the effect of stiffener dimensions indicated that stiffeners dimensions if having minimum area and moment of inertia requirements don’t effect on rotation angle capacity.
Link beam,cross-section,rotation,stiffener,eccentrically braced frame
تیرپیوند,مقاطع عرضی,زاویه دوران,سختکننده,قابهای مهاربندی شده برونمحور
1
13
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-1331&slc_lang=fa&sid=16
2012/04/292014/01/15
1392/10/25
2013/05/162013/12/22
1392/10/1
S.
Ebrahimi
Tarbiat Modares University
سمیرا
ابراهیمی
00319475328460050697
00319475328460050697
No
دانشگاه تربیت مدرس
H.
Shakib
Tarbiat Modares University
حمزه
شکیب
00319475328460050698
00319475328460050698
Yes
دانشگاه تربیت مدرس
M.
Soltani Mohammadi
Tarbiat Modares University
مسعود
سلطانی محمدی
00319475328460050699
00319475328460050699
No
دانشگاه تربیت مدرس
fa
شبیه سازی و بررسی اثر عوامل موثر بر حرکت تصادفی ذرات رسوب بار بستر در جریان ماندگار
Modeling the saltation and evaluating the parameters affecting the random movement of sediment particles in bed load transport under steady flow
بررسی انتقال رسوب در مقیاس حرکتذرات باعث شناخت بهتر پدیده انتقال رسوب و تعیین نرخ آن در محیط های رودخانه و دریا می گردد. ذرات رسوب عمدتاً به دو صورت بار معلق و بار بستر تحت تاثیر جریان و یا امواج منتقل می شوند . بار بستر خود به صورت های لغزش، غلتش و پرش انتقال می یابدکه در میان آنها پرش غالب می باشد. در این فرایند پرش عوامل متعددی تاثیر گذار هستند. اما به دلیل روشن نبودن کامل این عوامل ، پدیده ی پرش ذره تا حدی تصادفی در نظرگرفته می شود. از جمله ی این عوامل می توان بهاثر شکل ذره، محل قرارگیری آن و آشفتگی جریاناشاره نمود. در این مقالهمیزان پرش ذرات وسرعت متوسط آنها و تاثیر عوامل یاد شده برآن در جریان ماندگار با استفاده از یک مدل ریاضی مورد بررسی قرار می گیرد.از عواملی که به طور ویژه مورد توجه قرار گرفته است تاثیر شکل ذرات و محل قرارگیری آن بر روی طول و سرعت پرش ذره می باشد. همچنین یک رابطه منطقی بین سرعت و زاویه اولیه پرش و محل قرارگیری آن در بستر برقرار گردیده است.ازنتایج مطالعات حاضر در شناخت و تخمین دقیقتررفتار و نرخ رسوب بستر استفاده می گردد.
Study on the physics of sediment particle movement in micro scale is essential for better understanding sediment transport phenomenon and estimating the rate of sediment transport in rivers and marine environment. Sediment particles basically transport in two modes of bed and suspended load. Bed load takes place through sliding, rolling and saltation. Many parameters influence on this process, which their effects are not fully understood. In this research the influence of the affecting parameters on movement of sediment particles in saltation under unidirectional steady flow are investigated. First, a numerical model is developed to simulate the particle motion in bed load saltation. Then the influencing parameters such as particle shape and its position between other particles, upon the jump length and average velocity of the particles are studied. The result of the study improves our understanding and results in better estimation of sediment transport rate for engineering application.
sediment transport,bed load,steady flow,saltation,Numerical Modeling
پرش,شکل ذره,محل قرار گیری ذره,جریان ماندگار,بار بستر
11
11
http://mcej.modares.ac.ir/browse.php?a_code=A-16-14231-1&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/15
1390/5/24
2013/05/162013/12/222013/08/12
1392/5/21
saeed
kaboorani
سعید
کبورانی
00319475328460056113
00319475328460056113
Yes
دانشجو
ahmad
shanesaz zade
Assistant Professor, Faculty of Engineering, University of Isfahan
احمد
شانه ساززاده
00319475328460056112
00319475328460056112
No
استادیار دانشکده فنی و مهندسی دانشگاه اصفهان
fa
ارائه مدلی برای افزایش فاصله و کاهش ابعاد سخت کننده های تیرپیوند قوطی شکل قاب های مهاربندی شده برون محور
A model for increasing the distances and decreasing the dimensions of stiffeners for tubular link beams in eccentrically braced frames
تیرهای پیوند با مقطع عرضی قوطی در قاب های مهاربندی شده برون محور به دلیل دارا بودن پایداری پیچشی ذاتی برخلاف تیر های پیوند I شکل، نیاز به مهارجانبی ندارند و کمانش پیچشی جانبی در آن ها کمتر رخ می دهد با این وجود مقاطع عرضی I شکل به دلیل حاکم بودن شرایط مرزی گیردار در تمام وجوه ورق جان نسبت به ورق جان مقاطع عرضی قوطی که داری شرایط مرزی ساده هستند، دارای مزیت می باشند. در این تحقیق، تیرهای پیوند با مقاطع عرضی قوطی و I شکل مختلف در محدوده غیرالاستیک مورد بررسی قرار گرفته اند و سعی شده است که با تغییر در نحوه آرایش سخت کننده های تیر پیوند قوطی شکل، افزایش فواصل و کاهش ابعاد آن ها حاصل شود. برای انجام مطالعات عددی از نرم افزار اجزاء محدود و پروتکل بارگذاری AISC 2005 استفاده شده است. بررسی عددی مدل های مختلف تیرپیوند نشان می دهند که چنانچه تیرهای پیوند I شکل و قوطی دارای مشخصات هندسی یکسان باشند تیرهای پیوند I شکل به دلیل عملکرد بهتر ورق جان، از ظرفیت دوران بالاتری برخوردار هستند. همچنین بررسی نتایج نشان می دهد که آرایش جدید سخت کننده های تیرپیوند قوطی باعث افزایش فواصل و کاهش ابعاد آن ها شده به گونه ای که بر ظرفیت زاویه دوران نیز تأثیر نامطلوبی نمی گذارد. همچنین بررسی ها نشان می دهند که ابعاد سخت کننده ها در صورت ارضاء مساحت و ممان اینرسی مورد نیاز تأثیری روی ظرفیت زاویه دوران ندارند.
Tubular cross-sections of link beams have substantial torsional stability, making them less susceptible to lateral torsional buckling than I-shaped cross-sections in eccentrically braced frames, and may thus not require lateral bracing. Web of I-shaped cross-sections because of having clamped boundary conditions in its four sides than web of tubular cross-sections that have simply supported boundary conditions in its four sides, having advantage. In this study, link beams with different tubular and I-shaped cross-sections in non-elastic limits are investigated and has been tried by changing link beams stiffeners array cause increasing the distances and decreasing the dimensions of them. For this purpose nonlinear finite element software and AISC-2005, loading protocol are used.The numerical result of different link beams models indicate that tubular and I-shaped cross-sections if having same geometric profile, I-shaped cross-sections have higher rotation capacity because of better performance of their web. So study of results indicate that new arraying of stiffeners of tubular link beam inceases increasing the distances and decreasing the dimensions of them and doesn’t have any bad effect on rotation angle capacity of them. An investigation of the effect of stiffener dimensions indicated that stiffeners dimensions if having minimum area and moment of inertia requirements don’t effect on rotation angle capacity.
Link beam,cross-section,rotation,stiffener,eccentrically braced frame
تیرپیوند,مقاطع عرضی,زاویه دوران,سخت کننده,قاب های مهاربندی شده برون محور
11
11
http://mcej.modares.ac.ir/browse.php?a_code=A-16-1000-6644&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/12
1389/11/23
2013/05/162013/12/222013/08/122013/12/22
1392/10/1
samira
ebrahimi
سمیرا
ابراهیمی حسین آبادی
00319475328460056093
00319475328460056093
No
دانشجو - دانشگاه تربیت مدرس
Hamzeh
Shakib
حمزه
شکیب
00319475328460056092
00319475328460056092
Yes
استاد دانشگاه / دانشگاه تربیت مدرس
Masood
Soltani Mohammadi
مسعود
سلطانی محمدی
00319475328460056091
00319475328460056091
No
استاد دانشگاه / دانشگاه تربیت مدرس
fa
ارائهی مدل ارزیابی خطر ریزش بهمن در محورهای کوهستانی (مطالعه موردی: محور کرج-چالوس)
Presentation a Risk Model of Avalanche Points in Mountainous Roads
(Case Study: Chalous- Karaj Road)
ریزش بهمن در جادههای کوهستانی ایران یکی از حوادثی است که در ماه های سرد سال امکان وقوع دارد و موجب مسدود شدن برخی از جادههای اصلی کشور میشود. این موضوع به خصوص در مسیرهای ارتباطی بین پایتخت و شمال کشور بیش تر مشهود است. ارزیابی و بررسی وضعیت بهمنخیزی نقاط جاده با استفاده از جمع آوری اطلاعات و در صورت نیاز، مطالعات میدانی و تهیه ی عکس های هوایی انجام میپذیرد. دراین خصوص جمع آوری اطلاعات منطقهای، پایداری شیب، زمین شناسی، تعدد و تکرر و ترافیک جاده ضروری است. در این تحقیق، با استفاده از روش تحلیل سلسله مراتبی(AHP)1 میزان اهمیت هر یک از اطلاعات و پارامترهای مذکور تعیین می شود. روش کار بدین صورت است که با نظرسنجی از خبرگان و کارشناسان، وزنهای نسبی و سپس با به کارگیری نرم افزار EXPERT CHOICE میزان وزنهای نهایی هر پارامتر تعیین می شود؛ در نتیجه مدل خطرسنجی ریزش بهمن که میزان ریسک ریزش بهمن را در نقاط مختلف محورها نشان می دهد، تعیین خواهد شد. مدل مذکور در محور کرج- چالوس که بین استان های البرز و مازندران قرار دارد و یکی از 4 شریان اصلی ارتباطی بین پایتخت و شمال کشور است، به کارگرفته شد و میزان خطر نقاط مختلف ریزش بهمن با روش فوق مشخص شد. براساس روش فوق 15 نقطه ی دارای خطر ریزش بهمن در جاده ی کرج- چالوس و اولویت هر نقطه به لحاظ ریسک تعیین شد که به ترتیب نقاط واقع در کیلومترهای 65، 73 و 60 از مبدأ کرج خطر بیش تری دارند و باید روشهای ایمنسازی در مقابل بهمن برای آن ها به کار گرفته شود.
Falling avalanche is one of incidents that may happen during cold months of winter in Iran. This event may lead to closure of some main roads of the country. Road closure is a challenging issue, particularly on roads connecting Tehran capital to the northern cities.
Detecting avalanche prone locations on roads is usually conducted by data gathering, surveying and investigating aerial photos. Field investigation usually requires collecting regional data including slope stability, geology and number and repetition of road traffic. In this study importance of each parameter was determined By an AHP method.
After interviewing experts, importance of each parameter was determined pair wise. Final weights for each parameter were also determined using Expert Choice software. Searching for important contributing parameters and methods for measuring risk of avalanche in mountainous roads in the literature, main parameters of falling avalanche were selected and used in this study. It is obvious that many of recognized parameters should be considered in every effort of measuring danger. That is why such parameters are similarly used in most methods.
The most important reference for categorizing the methods of risk measuring was guidelines on preventing falling stones and avalanche published by US National Institute of Highways and the Main Office of Highways. In these guidelines, traffic repetition is taken as an important factor increasing the risk after a falling event happens.
This study framed the experts’ opinions and optimized risk analysis with regards to local geotechnical and geologic conditions in Iran. Experts selected the snow depth, hillside slope, vegetation condition on hillside and number and repetition of the road traffic. Importance of parameters were calculated as 44.1% for traffic number and repetition, 19.1% for the hillside slope, 17.2% for vegetation, 15.6% for snow depth and 4% for traffic rate. These parameters were selected as the factors contributing in avalanche. In continue each parameter was rated in a four level category (very high, high, medium and low).
Model of avalanche danger calculates the avalanche risk in every point in a road network and all roads can be evaluated in terms of the danger of potential avalanche. For example the model was applied on Karaj-Chalus highway connecting Alborz to Mazandaran provinces. This highway is an important arterial between the capital and the northern cities. Using the method, 15 dangerous avalanche prone locations were determined and prioritized. They are located at 65, 73 and 60 km from Karaj. Preventive efforts should be taken for maintaining these locations and keeping them safe against potential avalanches
risk,Avalanche,Mountainous Roads,AHP
ریسک,ریزش بهمن,جاده های کوهستانی,روش تحلیل سلسلهمراتبی(AHP)
15
28
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-5760&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/15
1392/10/25
2013/05/162013/12/222013/08/122013/12/222013/12/22
1392/10/1
M.
Asadamraji
., M.Sc of Highway and Transportation of Tarbiat Modares Uni
مرتضی
اسدامرجی
00319475328460050536
00319475328460050536
No
پژوهشگر ارشد پژوهشگاه حمل و نقل طراحان پارسه
M.
Saffarzadeh
TarbiatModares
محمود
صفارزاده
00319475328460050653
00319475328460050653
Yes
دانشگاه تربیت مدرس
Sh.
Hassanpour
Ayat- allah- Borujerdi
شهاب
حسنپور
00319475328460050687
00319475328460050687
No
دانشگاه آیت الله بروجردی
N.
Rasooli
نغمه
رسولی
00319475328460050686
00319475328460050686
No
دانشگاه آزاد
fa
بررسی تجربی خطرپذیری آتشسوزی و همبستگی پارامترهای خطر آتشسوزی برای برخی مصالح ساختمانی پلیمری
An Experimental Assessment of Fire Hazard and Correlations of Fire Parameters for Some Polymeric Building Materials
رفتار ده ماده ساختمانی پلیمری در برابر آتش با گرماسنج مخروطی در تابش kW/m2 50 آزمایش شد. خطرپذیری این مواد در آتش سوزی شامل حرارت و دود آزاد شده، با روش های گوناگون بررسی و بحث شد. بیش تر مواد بررسی شده، رفتار خطرناکی برای آتش داشتند. از دید حرارتی، نمونههای MDF، موکت و اپوکسی و از دیدگاه دود و سمیت، نمونههای پلی کربنات و اپوکسی بسیار خطرناک نشان دادند. بنابراین برای به کار بردن این مواد در ساختمان باید مقررات مناسب، تدوین و محدودیت های کاربرد آن ها مشخص شود. پارامترهای حرارتی ناشی از سوختن مواد، با هدف ارزیابی خطر آن ها در گسترش آتش سوزی بررسی شد. نتایج نشان داد که پارامترهای زمان افروزش، شدت رهایش گرما و کل رهایش گرما، مهم ترین ویژگی ها برای تعیین خطر گسترش آتش سوزی است. زمان افروزش بر زمان وقوع گُر گرفتگی در اتاق و سرعت پیشروی سطحی شعله بر نازک کاری ها تأثیر مهمی دارد و نادیده گرفتن آن می تواند به پیش بینی اشتباه خطر گسترش آتش سوزی منجر شود. از دیدگاه سمیت، منحنی منوکسید کربن کنار پارامتر سمیت میتواند برای ارزیابی خطر سمیت به کار رود.
The use of polymeric and flammable building materials has been considerably increased in construction industry of Iran in recent years. Most of these materials are highly flammable and can seriously contribute in growth of a probable fire in buildings. In this research, the fire behavior of some polymeric building materials used as finishes was evaluated with cone calorimeter method at 50 kW/m2. The thermal fire parameters and smoke toxicity produced from the burning specimens were assessed; including time to ignition, flaming duration, peak of heat release rate, total heat release, smoke production rate, average specific extinction area, carbon dioxide and carbon monoxide production. The correlation between the thermal parameters was discussed and it was concluded the total heat release had direct dependence on combustible nature of the material and the surface density and reverse dependence on time to ignition. Meanwhile, the fire toxicity hazard parameters including carbon monoxide production rates and smoke toxicity were evaluated. The smoke toxicity was expressed in terms of the two parameters: fractional effective dose (FED) and toxicity index (LC50). The obtained results showed that the most tested materials had a dangerous behavior in case of fire and can cause flashover in the room. They released considerable amount of heat with high peaks of heat release rate. Especially epoxy, MDF and polycarbonate samples showed a high potential for contribution in fire growth. In addition, the epoxy, PVC and polycarbonate produced the highest amounts of smoke and carbon monoxide. It should be noted that the production amount of carbon monoxide was measured in an open system in which air is circulated with a certain velocity. So in a real fire, these values can be accumulated and increased in the room of fire. Among the tested samples, polycarbonate (PC) and PVC flooring (PVC-F) showed the highest value of FED, however it seems that the assessment of carbon monoxide versus time could provide more important information for assessment of smoke toxicity. The results showed that it is needed to regulate the fire behavior of building finishes and restrict their application in buildings. For this purpose, a fire risk classification was needed, which will be studied in further steps of the research.
Fire safety,fire risk,building code,smoke toxicity,cone calorimeter
ایمنی برابر آتش,خطر آتشسوزی,مقررات ساختمانی,پتانسیل دود و سمیت,گرماسنج مخروطی
29
40
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-6782&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/15
1392/10/25
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/22
1392/10/1
S.
Bakhtiyari
Building Dept., Building & Housing Research Center
سعید
بختیاری
00319475328460050695
00319475328460050695
Yes
مرکز تحقیقات ساختمان و مسکن
L.
Taqikhani
لیلا
تقیاکبری
00319475328460050694
00319475328460050694
No
مرکز تحقیقات ساختمان و مسکن
M.
Jamali Ashtiyani
مسعود
جمالی آشتیانی
00319475328460050693
00319475328460050693
No
مرکز تحقیقات ساختمان و مسکن
fa
رفتار لرزهای قاب فولادی خمشی دارای دال مجوف حبابی و استوانهای تحت زلزلههای حوزه نزدیک با استفاده از مدلسازی اجزاء محدود
Dynamic Nonlinear Analysis of Bubble Decks Reinforced Concrete and other Slabs
در این مقـاله رفتار قاب های دارای سه نوع دال مجوف حبابی، مجوف استوانه ای و بتنی توپر تحت اثر زلزله های حوزه نزدیک مطالعه شده است. نتایج نشان می دهد که دال حبابی در مقایسه با سایر دال ها مقاومت و سختی قاب را افزایش داده و تحت شتابنگاشت با PGA بزرگتر و تغییر مکان کوچکتری به مکانیسم می رسد. همچنین میزان جذب انرژی در این نوع قاب بیشترین و در قابی با دال مجوف استوانه ای کمترین است. در قاب با دالهای مجوف سهم ستون ها در اتلاف انرژی بیشتر از تیرها ولی در قاب با دال توپر این سهم در تیرها بیشتر است. نحوه تشکیل مفصل پلاستیک در اعضا و پیشرفت خطوط تسلیم در دال های مجوف کاملا با دال توپر متفاوت است. دال توپر و دال مجوف استوانه ای همزمان با قاب به مکانیسم می رسند اما در دال حبابی هنگامی که قاب فولادی به مکانیسم می رسد، هنوز کل دال گسیخته نشده است.
In this paper the behavior of framee, the process of plastic hinge formation and energy absorption of frames with two spans and one floor with three types of slab including bubble deck slab, hollow core slab and reinforced slab under three earthquake accelerations have been analyzed and compared. The results show that bubble deck slab and hollow core slab as rigid as normal reinforced slab, although bubble deck slab has higher strength and stiffness compared to other slabs. Partnering slab in analysis make period of slab reduce more over bubble deck slab and hollow core to the comparison of reinforced slab, have more effect on period reduction. Ultimate displacement of frame with reinforced slab reach to failure mechanism is more than two mentioned case, however frame with bubble deck slab reach to failure mechanism under stronger earthquake acceleration and smaller displacement than reinforced slab. Comparison base shear of three discussed case shows that maximum base shear is in bubble deck slab and minimum base shear is in normal reinforced slab. Formation of plastic hinge in frame with bubble deck slab is similar with that in frame with hollow core slab with the difference that plastic hinge in former occurs later at the top end of the middle column and two ends of middle beams. In fact, formation of plastic hinges in this frame requires higher acceleration because of the higher amount of concrete and stiffness. In all samples, plastic hinge first occur in the frame and then yielding lines occur in the tensile region of the slabs. The failure mechanism of slab and steel frame occur at the same time in frame with hollow core slab and reinforced slab; however, this is not the case in the frame with bubble deck slab and even though with occurring of yielding lines, the slab does not fail. The stress distribution due to gravity loads is symmetric across all the slabs; however, the increase rate of stress is different. This difference is particularly notable in seismic behavior of slabs in a way that the formation of plastic hinge and yielding lines in hollow core slab, because of the holes, is totally different with that of in reinforced slab. In comparison with other slabs and due to the formation of plastic hinge, reinforced slab absorb lower energy. Columns, beams and connections play different role in energy dissipation. In all frame, the contribution of connections to dissipate energy is minor and this is because yielding does not occur in connections. Contrary to the frame with reinforced slabs, because of yielding in several places of columns, columns dissipate energy more than beams in the frames with hollow core slabs. It was concluded that hollow core slab and bubble deck slab have maximum and minimum contributions to the energy dissipation, respectively.
Steel frame,nonlinear dynamic analysis,Finite Element Modeling,Hollow core slab,Bubble deck slab,Reinforced slab
زلزله حوزه نزدیک,قاب فولادی,تحلیل غیرخطی دینامیکی,مدلسازی اجزاء محدود,دال مجوف حبابی,استوانهای و توپر
41
51
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-642&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/152014/01/15
1392/10/25
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/222013/12/22
1392/10/1
mojtaba
fathi
مجتبی
فتحی
00319475328460052349
00319475328460052349
Yes
دانشگاه رازی کرمانشاه
dariush
asadizade
داریوش
اسدیزاده
00319475328460052348
00319475328460052348
No
دانشگاه رازی کرمانشاه
fa
بررسی مطلوبیت روش بارش ماسه برای نمونهسازی خاکهای ماسهای در مدلهای آزمایشگاهی
Investigation of Desirability of Sand Pluviation Technique in order to Sample Making of Sandy Soils for Laboratory Models
روش باران ماسه یا به عبارت دیگر «بارش ماسه در هوا»، روشی برای آماده سازی مدل های آزمایشگاهی است که به منظور انجام برخی آزمایش های خاص، مانند کالیبراسیون نفوذسنج های استاتیکی و دینامیکی به کار می رود. هنگام استفاده از مدل های آزمایشگاهی، کالیبره شدن دستگاه نمونه ساز به منظور تولید دقیق نمونه هایی با شرایط دلخواه و دانسیته ی نسبی، اهمیت دارد. این مقاله به بررسی نتایج به دست آمده از کاربرد دستگاه نمونه ساز به روش بارش ماسه، برای ایجاد نمونه های ماسه ای در دانسیته های مورد نظر پرداخته است. در این راستا با ترکیب آرایش های مناسب برای قطر منافذ صفحات بارش، فاصله ی منافذ و ارتفاع بارش، می توان به دانسیته ی نسبی ماسه ی مورد مطالعه دست یافت. نتایج نشان می دهد که این روش، توانایی تولید نمونه های ماسه برای مدل های آزمایشگاهی در دانسیته های نسبی 20 تا 100 درصد را دارا است و می توان ماسه ای با شرایط یکنواخت ایجاد نمود. به طور کلی در حالتی که سرعت بارش پایین است، می توان به دانسیته های نسبی بالاتر و متعاقب آن وزن واحد حجم بالاتری دست یافت. همچنین این موضوع که در حالت ارتفاع بارش بیش از 500 میلی متر، تغییری در میزان دانسیته به دست آمده ایجاد نمی شود، نیز تایید گردید.
Dry pluviation, or the “raining of sand through air”, is a commonly employed technique used to prepare sand samples in the laboratory to some specified initial state. It is important, however, that the techniques are calibrated so that the density of the samples produced is known accurately and precisely. Several methods have been used to prepare sand samples for use in experimental studies. This paper presents the results of a study in which the characteristics of pluviated samples of Stockton Beach silica sand are determined as a function of deposition rate and free-fall height. The experimental arrangement used to generate the data for this study is a simple set with 500 mm of diameters mold. Sand was rained from the hopper, through holes ranging in size from 6mm to 15mm diameter, at spacing’s (S) ranging from 20 to 100mm, with holes arranged in a triangular pattern. In all cases, a single diffuser screen, with an aperture size of 2.36mm was employed (except where the pluviation rate was so great that sand accumulated on the screen, at which point, the diffuser was removed). The fall heights (free fall distance traveled by the sand from the diffuser to the top of mould) considered were 61mm, 236mm, 481mm, 641mm. A 1 liter sampler mold was used to catch the sand. The dry pluviation technique is an effective method of preparing sand samples to a wide range of target densities. A comprehensive set of data has been obtained and reported to assist in the design of pluviation systems. Data is also provided on the consistency of the achieved densities, and how this varies as a function of the target density. In general, it is found that the higher densities achieved under slower rates of deposition are more repeatable. There is no unique relationship between shutter porosity and the deposition rate, but rather there is a trend for shutters with fewer, larger holes to achieve significantly greater deposition rate than shutters with a greater number of smaller holes, with the same porosity. Clearly, retardation of flow at the margins of the shutter holes is reduced in situations of fewer, larger holes, as the ratio of circumference to area is smaller in these cases. The results show that samples with relative densities from around 20% to 100% are readily achieved by simple combinations of hole size and hole spacing. In general, it is apparent that the dry pluviation techniques is more suited to the preparation of samples of greater density, with many combinations of hole size and hole spacing able to achieve relative densities between about 70 and 90%. Densities between 20 and 60% are achieved less readily, while densities below 20% are the least readily achieved. Previous observations that sand fall heights greater than 0.5m have no affect on density are confirmed by the results of this study
Sample making set,pluviation intensity,relative density,holes arrangement,pluviation plate
دستگاه نمونهساز,شدت بارش,دانسیتهی نسبی,آرایش منافذ,صفحهی بارش
53
63
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-4465&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/152014/01/152014/01/18
1392/10/28
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/222013/12/222013/12/22
1392/10/1
S.D.
Mohammadi
Bu-Ali Sina University
سید داود
محمدی
00319475328460050712
00319475328460050712
Yes
دانشگاه بوعلی سینا
R.
Ajalloeian
Isfahan University
رسول
اجل لوئیان
00319475328460048033
00319475328460048033
No
دانشگاه اصفهان
fa
ارزیابی مقاومسازی لرزهای قابهای فولادی مهاربندی شده بهکمک دیوارهای برشی فولادی
Evaluation of Seismic Strengthening of Steel Braced Frames using Steel Shear Walls
استفاده از دیوارهای برشی فولادی به دلیل مزایای فراوانی که نسبت به سایر سیستمهای مقاوم در برابر زلزله دارند، قابل توجه است. از مزایای این سیستم میتوان به شکل پذیری و جذب و استهلاک انرژی زیاد با وجود سختی بالا و اقتصادی بودن آن اشاره کرد. با عنایت به خطر لرزهخیزی بالا و نیاز به مقاوم سازی بسیاری از ساختمانها در برابر زلزله، استفاده از این سیستم لرزهبر، مناسب و مقرون به صرفه بهنظر میرسد. در تحقیق حاضر به بررسی مقاوم سازی قابهای فولادی مهاربندی شده همگرا با استفاده از دیوارهای برشی فولادی پرداخته شده است. تمرکز پژوهش بر روشهایی است که در آنها مقاوم سازی تنها با اضافه کردن المانهای دیوار برشی فولادی به قاب مهاربندی شده صورت میپذیرد. ابتدا تعدادی قاب فولادی مهاربندی شده ی غیرمقاوم به عنوان قابهای پایه انتخاب و مدل سازی شده اند. قابهای پایه با اضافه کردن پانلهای فولادی به روشهای مختلف، مقاوم سازی می شوند. سپس همه قابهای پایه و قابهای مقاوم سازی شده به صورت استاتیکی غیرخطی تحلیل می شوند. از مقایسه ی مدلهایی که در آنها بهسازی لرزهای بهکمک تعویض سیستم لرزهبر از مهاربندهای فولادی همگرا به دیوارهای برشی فولادی صورت پذیرفته است، با سایر روشهای مقاوم سازی مورد مطالعه، میتوان به رفتار لرزهای بهبودیافته ی قابهای بهسازی شده پیبرد. مطالعه ی حاضر نشان میدهد در قابهای فولادی مهاربندی شده، با رعایت پارهای نکات علمی، فنی و اجرایی، تعویض سیستم باربر جانبی از مهاربندهای فولادی همگرا به دیوار برشی فولادی نازک، میتواند به عنوان روشی مناسب برای مقاوم سازی و بهسازی طیف وسیعی از قابهای فولادی موجود، استفاده شود.
In recent years using steel plate shear wall system, because of its advantages in comparison with other earthquake resistant systems, has been a matter of attention. Some of its advantages relative to other systems include abundance advantage, high ductility, good hysteretic behavior and energy absorption capacity, high stiffness and economic advantages. Regarding that in Iran there is high seismicity risk and the need to strengthen old and unsafe urban textures and buildings, using this system as a lateral load resistant system seems appropriate and economical. In the present research strengthening of x-braced steel frames with steel plate shear walls is evaluated. Addition of bracing to unbraced frame spans, substituting braces with thin steel shear wall panels and adding thin steel shear wall panels to unbraced spans which do not have architectural requirements are considered as retrofitting strategies. The focus is on the methods in which retrofitting is only done by adding steel plate shear wall elements to braced frames. Some of these methods have many economic and practical advantages. Others are only proper for some special cases. In this study a number of x-braced steel frames designed by the first edition of Iranian code of practice for seismic resistant design of buildings (Iranian Standard No. 2800) are taken as basic frames which need to be retrofitted. These basic frames are retrofitted by adding steel panels with different methods. Then nonlinear static analysis (pushover analysis) with displacement control pattern has been done on both basic and retrofitted finite element frame models and the capacity curves (diagram of story displacements against base shear) of basic frames and retrofitted frames are compared. Considering the results of the pushover analysis of models in which seismic retrofitting is done by replacing x-bracing earthquake resistant system with steel plate shear walls and the results of other methods of strengthening, it is seen that seismic behavior of retrofitted frames is more desirable in terms of overstrength factor (Ω) and overall ductility of structure ( ). The failure and fracture mode in most of the medium-rise frames was ductile but in the short-rise frames the fracture was brittle. Thus, replacing the braces in short-rise structure with thin steel shear walls seems irrational and unjustified economically. But it is to be mentioned that strengthening and increasing the moment of inertia of the adjacent columns of steel shear wall panels in structures with brittle fracture mode could result the change from brittle to ductile fracture. The results of this research show that in the case of steel braced frames with regard to some scientific, technical and practical points; replacing concentric steel bracing earthquake resistant system by steel plate shear walls can be used as a suitable method for retrofitting a wide range of existing steel structures in Iran.
steel shear walls,eccentric braced frames,nonlinear static analysis,seismic resistant system,seismic rehabilitation
دیوار برشی فولادی,قابهای فولادی مهاربندی شدهی همگرا,تحلیل استاتیکی غیرخطی,بهسازی لرزهای
65
78
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-8014&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/152014/01/152014/01/182014/01/18
1392/10/28
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/222013/12/222013/12/222013/12/22
1392/10/1
A.
Massumi
Kharazmi University
علی
معصومی
00319475328460050702
00319475328460050702
Yes
دانشگاه خوارزمی
M.
Shekari
Kharazmi University
مهدی
شکاری
00319475328460050701
00319475328460050701
No
دانشگاه خوارزمی
M.
Ahmadi
Kharazmi University
مصطفی
احمدی
00319475328460050700
00319475328460050700
No
دانشگاه خوارزمی
fa
بررسی آزمایشگاهی اثر شرایط هیدرولیکی ورودی بر ساختار جریانهای گلآلود
Experimental Investigation of Entrance Hydraulic Condition Effects on Flow Structure in Turbidity Currents
- رسوبات انباشته شده در مخازن سدها، گنجایش مخزن را بسیار کاهش می دهد. جریان های گل آلود در جابه جایی و رسوبات ریزدانه در مخازن سدها، نقش مهمی دارند. در این پژوهش، اثر تغییرات شرایط هیدرولیکی ورودی جریان گل آلود بر ویژگی هایی از پیشانی، بدنه و ساختارهای آشفتگی موجود در جریان گل آلود، بررسی آزمایشگاهی شده است. این ویژگیها با یک دوربین فیلم برداری و یک دستگاه سرعتسنج صوتی، اندازهگیری شده است. نتایج نشان می دهد که با کاهش عدد فرود چگالی ورودی، سرعت پیشانی و بیشینه سرعت، در بدنه جریان افزایش مییابد. مقادیر مثبت تنش برشی رینولدز نزدیک کف نشان میدهد که در این بخش، پدیده حاکم، جاروبی یا بیرونرانی است در حالی که در فصل مشترک جریان گل آلود و سیال محیطی، پدیده اندرکنش رو به بیرون یا اندرکنش رو به داخل، حاکم است.
Water-storage capacity of reservoir reduces mainly due to sediment laden. Turbidity current has an important role on sediment transfer in reservoir. It is necessary to study sediment interaction and flow in order to predict mechanism of turbidity current. In this paper effects of changes in entrance hydraulic condition of turbidity current on head velocity, layer-average thickness, layer-average velocity, body velocity and turbulent structure have investigated experimentally. The front velocity of the head of turbidity current was determined by video recording and body velocity and turbulence parameters measured by Vecterino. When the initial Froude number decreases the maximum velocity increases in body and head. Positive shear Reynolds stress near bed indicates that major contributor in this region is sweep or ejection while major contributor near interface is inward interaction or outward interaction. Entrainment is dominated at interface. The investigation shows that head velocity depends on inlet Froude number and inlet Reynolds number. Variation of head velocity along channel is exponential. The maximum reduction of head velocity takes place at whereas variation of head velocity at is negligible. Driving forces at are inertial force and gravity force. Driving force decreases after hydraulic jump and only gravity force remains as driving force. Therefore head velocity is constant at . Head velocity increases when inlet Reynolds number increases. Body velocity increases when inlet Froude number decreases, as gravity force increases when inlet Froude number decreases. Effects of inlet Froude as number on body velocity is negligible at the end of channel. Negative value of body velocity at the interface of turbidity current and ambient fluid indicates entrainment phenomenon at this region. When inlet Froude number decreases, vertical component of velocity increases too,then maximum velocity approaches to the bed. Elevation of maximum velocity increases along the channel due to sedimentation of particles and decreases of vertical component of velocity. Body velocity decreases along the channel due to decrease of inertial force. Vertical Reynolds stress decreases when inlet Froude number decreases. Because of increase in particle turbulence dissipates and therefore vertical Reynolds stress decreases. Oscillation of vertical Reynolds stress is due to turbulence at this region. The maximum of vertical Reynolds stress tacks place near bed and interface of turbidity current and ambient fluid and minimum of vertical Reynolds stress tacks place near maximum velocity elevation. Shear Reynolds stress have two maximum values. One is near the bed and the other one is near the interface of turbidity current and ambient fluid. Maximum Reynolds shear stress is positive near bed and negative near interface. Minimum of Reynolds shear stress take place near maximum velocity elevation.
inlet Froude number,head velocity,Reynolds stress,body velocity,layer-average velocity,layer-average thickness
عدد فرود چگالی ورودی,سرعت پیشروی جریان,تنش های رینولدز,سرعت بدنه جریان,سرعت میانگین جریان گلآلود,ارتفاع میانگین جریان گلآلود
79
94
http://mcej.modares.ac.ir/browse.php?a_code=A-10-1000-3892&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/152014/01/152014/01/182014/01/182014/01/18
1392/10/28
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/222013/12/222013/12/222013/12/222013/12/22
1392/10/1
M.
Naji Abhari
Tarbiat Modares University
ماندانا
ناجیابهری
00319475328460050718
00319475328460050718
No
دانشگاه تربیت مدرس
M.
Ghosian
Tarbiat Modares University
مسعود
قدسیان
00319475328460061352
00319475328460061352
Yes
دانشگاه تربیت مدرس
Bahar
Firoozabadi
Sharif University
بهار
فیروزآبادی
00319475328460050716
00319475328460050716
No
دانشگاه صنعتی شریف
fa
ارزیابی مقاومت بیرون کشش صندوقه های مکشی در خاک ماسه ای با استفاده از مدل فیزیکی
A laboratory Investigation into the Pull-out Capacity of Upright and Tapered Suction Caissons in Sand
در دو دهه گذشته، صندوقه های مکشی به عنوان سازه های کارآمد و اقتصادی به عنوان پی در صنایع فراساحل مورد استفاده قرار گرفته اند. در این مقاله مقاومت بیرون کشش صندوقه های مکشی در خاک ماسه ای مورد بررسی قرار گرفته است. صندوقه های مکشی مورد مطالعه، به دو شکل دیواره قائم و دیواره شیبدار ( شیب 1: 10) با قطر متوسط خارجی 80 میلیمتر بوده و نسبتهای ظاهری آنها برابر 1، 2، 3 و 4 میباشد. اعمال بیرون کشش بر صندوقه های مکشی تحت بار قائم به صورت کنترل تغییر مکان صورت پذیرفته، اثر هندسه صندوقه در مقاومت بیرون کشش آن مطالعه شده است. در این آزمایشها تاثیر تفاوت در چگالی خاک و نرخ بیرون کشش نیز بررسی گردید. مشاهده شده که صندوقه های مکشی با دیوار شیبدار مقاومت بیرون کشش بیشتری نسبت به صندوقه های مکشی قائم از خود نشان میدهند. صندوقه های مکشی دیوار شیبدار در تغییر مکان بیشتری به نسبت صندوقه های مکشی قائم به حداکثر مقاومت بیرون کشش خود میرسند. در هر دو نوع صندوقه با افزایش سرعت، حداکثر ظرفیت باربری بیرون کشش افزایش مییابد، اما صندوقه های مکشی با دیوار شیبدار به نرخ سرعت به نسبت صندوقه های مکشی قائم حساسیت کمتری دارند. در هر دو صندوقه با افزایش سرعت بیرون کشش مقدار جابجایی متناظر با حداکثر ظرفیت باربری، بیشتر میشود. با افزایش تراکم خاک، ظرفیت بیرون کشش هر دو نوع صندوقه افزوده میشود اما این افزایش برای صندوقه های مکشی با دیوار شیبدار به نسبت صندوقه های مکشی قائم بیشتر است.
During the past two decades, suction caissons have become an increasingly viable alternative to traditional offshore foundation such as gravity based foundations and piles. The pull-out performance of conventional suction caissons (with upright walls) has been previously investigated by a number of researchers. However, less attention has been formerly paid to tapered suction caissons. This paper reports some results from an experimental investigation into the pull-out performance of tapered suction caissons. The 1g experiments have been carried out on eight small scale suction caissons. The aspect ratios, (length/diameter) have been 1, 2, 3 and 4 and the diameter has been constant and equal to 80 mm. Four specimens have had upright walls while the other four had a positive wall slope of 10%. The caissons have been installed in a soil tank containing very fine saturated silty sand. The caissons have then been subjected to vertical pull-out loads with different speeds. The effects of variations in soil density and pull-out rate on the pull-out capacities have also been investigated. In general, tapered caissons have been noticed to present enhanced pull-out capacities as compared to those from their equivalent upright caissons. The enhancement rate has been found to be more significant in suction caissons with higher aspect ratios. With both upright and tapered caissons the pull-out capacity increases by an increase in the pull-out rate. The pull-out rate effects are more significant with upright caissons in comparison to the corresponding tapered caissons. The density effects, however, are more significant with tapered caissons as compared to their equivalent upright caissons.
Laboratory Investigation,Suction Caisson,Upright,Tapered,Pull-out
بررسی آزمایشگاهی,صندوقه مکشی,دیوار قائم,دیوار شیب دار,بیرون کشش
111
111
http://mcej.modares.ac.ir/browse.php?a_code=A-16-1000-6865&slc_lang=fa&sid=16
2012/04/292014/01/152011/08/152011/02/122014/01/152014/01/152014/01/152014/01/182014/01/182014/01/182010/08/29
1389/6/7
2013/05/162013/12/222013/08/122013/12/222013/12/222013/12/222013/12/222013/12/222013/12/222013/12/222013/08/12
1392/5/21
Siamak
Kakasoltani
Marzdaran Blv - No.237 - No.1
سیامک
کاکاسلطانی
00319475328460056047
00319475328460056047
Yes
مرزداران-نرسیده به اشرفی اصفهانی-روبروی بانک تجارت-پلاک 237-واحد 1
مصطفی
زین الدینی
00319475328460056046
00319475328460056046
No
خیابان ولیعصر-تقاطع میرداماد-دانشکده عمران دانشگاه صنعتی خواجه نصیرالدین طوسی
محمود رضا
عبدی
00319475328460056045
00319475328460056045
No
خیابان ولیعصر-تقاطع میرداماد-دانشکده عمران دانشگاه صنعتی خواجه نصیرالدین طوسی