@article{ author = {Fakhri, M. and Farokhi, m}, title = {Studying the Propagation of Top-Down Cracking (TDC) in Asphalt Concrete pavements by Means of Fracture Mechanics Theory}, abstract ={Abstract Fatigue can be expressed as the failure of asphalt concrete under repeated loading in such a way that stress induced in the asphalt layer could be less than ultimate strength of the material. Fatigue cracking in asphalt concrete layer can be classified into two types regarding the place of crack initiation and the type of crack propagation. The first type the cracks initiated in the bottom of asphalt layer and propagates upward. This type of cracking is produced in the thin asphalt layer. The second type of cracking which is produced in thick asphalt layer is initiated in surface area then propagates downward which is called Top-Down cracking. The second type of cracking is studied less compared to the first one. One type of fatigue cracking, is fracture mechanics approach in which the failure in asphalt mixture is related to number of repeated loading. In this study the fracture mechanics approach was implemented to understand the effective parameters in propagation of top-down cracking. as well as developing a model to interpret the crack propagation in pavement also some graphs were produced for different types of material and loading which gives the length of cracks versus the number of repeated loading. the results showed that with increasing the load distance from the initial place which is initiated the stress intensity factor is increased in mode Ι and mode ΙΙ. Also increasing the stiffness gradient in asphalt concrete due to temperature differential in top and bottom of asphalt layer or differential increasing between stiffness of asphalt surface and asphalt base course will be increased the stress intensity factor.}, Keywords = {Pavement,Asphalt,Top down cracking,Crack propagation,Fracture mechanics}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی نحوه ی گسترش ترک های بالا به پایین 1 در روسازی های آسفالتی، با استفاده از (TDC) فرضیه ی مکانیک شکست}, abstract_fa ={چکیده- خستگی عبارت است از پدیده ی شکست بر اثر تکرار بار، که تنش ایجاد شده توسط این بار ممکن است حتی به مراتب کوچک تر از مقاومت نهایی مصالح باشد .ترکهای ناشی از خستگی، در مقاطع آسفالتی، با توجه به مکان پیدایش و نحوه ی گسترش آنها دو دسته است .دستهی اول ترک هایی است که در بخش پایینی مقطع آسفالتی پدید می آیند و سپس با تکرار بار بهسمت بالا گسترش مییابند. پیدایش این نوع ترک ها در مقاطع آسفالتی با ضخامت کم، رایج است . دسته دوم که در روسازی های ضخیم ام کان پیدایش بیش تری دارند، از سطح روسازی، شروع شده و به سمت پایین گسترش می یابند. این دسته از ترکها، نسبت به دستهی اول تاکنون کمتر مورد توجه و مطالعه قرار گرفتهاند. یکی از روشهای متداول تحلیل و بررسی ترکهای ناشی از خستگی، روش مکانیک شکست است که در آن، گسیختگی حاصل از خستگی آسفالت، از آغاز ترک و پیشروی آن در ضخامت آسفالت، به تعداد دفعات بارگذاری ارتباط داده میشود. در این پژوهش، برای شناخت بهتر و درک بیشتر نحوهی گسترش ترکهای روبه پایین و پارامترهای مؤثر در آن، از روش مکانیک شکست استفاده شده و پدیدهی ترک و نحوه پیشروی آن در روسازی، تحلیل نظری میشود و نمودارهایی که نشانگر طول ترک بر حسب تعداد دفعات تکرار بار است برای حالات مختلف مشخصات مصالح و بارگذاری، استخراج شده است. نتایج نشان داد که با افزایش فاصلهی بار از محل ابتدایی ترک ایجاد شده، مقادیر ضریب شدت تنش در افزایش مییابد. همچنین افزایش شیب سختی بتن آسفالتی ناشی از اختلاف دمایی سطح II و مد I مد پایینی و بالایی و یا افزایش اختلاف سختی لایهی بتن آسفالتی و لایهی اساس، باعث افزایش ضریب شدت تنش میشود.}, keywords_fa = {Top Down کلید واژگان: روسازی,آسفالت,ترکهای,Top Down رشد ترک,مکانیک شکست}, url = {http://mcej.modares.ac.ir/article-16-1482-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-1482-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {barimany, Amier and SoltaniMohammadi2, M and Tasnimi, A.}, title = {Modeling and Analysis of Masonry Elements by Fixed Smeared Crack Approach}, abstract ={The objective of this research is to develop nonlinear constitutive models for performance evaluation of masonry members on the basis of continuum model and fixed smeared crack approach. The finite element program called "WCOMD", which has basically been developed for modeling and analyzing the reinforced concrete, is used as the basis for modeling and analyzing in this paper. Constitutive laws and yield criteria according to the available experimental results on masonry panels are improved, so that it would have the capability of modeling nonlinear anisotropic behavior of masonry. The post-cracking behavior of masonry in direction normal to the crack (tension softening) is calculated according to crack band theory and in terms of fracture energy and element size in finite element. Also, the effect of cracking on compression behavior of masonry is considered on the basis of compression field theory. The validity of behavior models and analysis methods is measured via analyzing available experimental results in field of masonry panels and masonry walls.}, Keywords = {Nonlinear analysis,Smeared crack,Constitutive law,Masonry,FEM}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {مدل سازی و تحلیل غیرخطی المان های مصالح بنایی به روش ترک پخشی ثابت}, abstract_fa ={چکیده- هدف از این تحقیق توسعهی مدلهای رفتاری غیرخطی و اعتبارسنجی آن برای ارزیابی رفتار اجزاء مصالح بنایی، برپایهی مدل پیوسته و روش ترک پخشی ثابت 1 است. برنامهی اجزا محدود که اساساً برای مدل سازی و تحلیل المانهای بتن مسلح تهیه شده به عنوان پایهی مدل- WCOMD سازی و تحلیل در این مقاله مورد استفاده قرار گرفته و مدلهای رفتاری و معیارهای تسلیم برمبنای نتایج آزمایش های موجود بر روی پانل های مصالح بنایی اصلاح شده است، به گونهای که قابلیت مدل- سازی رفتار غیرهمسان و غیرخطی مصالح بنایی را دارا باشد. رفتار پس از ترک خوردگی مصالح در جهت عمود بر ترک (نرم شدگی کششی 2) بر مبنای تئوری پهنای ترک 3 و برحسب انرژی شکست و اندازهی المان در اجزاء محدود مورد محاسبه قرار می گیرد و همچنین تأثیر ترک خوردگی بر رفتار فشاری مصالح بر مبنای تئوری میدان فشاری 4 منظور می شود. اعتبار مدلهای رفتاری و روش تحلیل با بررسی نتایج آزمایشگاهی موجود در خصوص پانلهای مصالح بنایی و دیوارهای برشی مصالح بنایی، سنجش و بررسی میشود.}, keywords_fa = {کلید واژگان: تحلیل غیرخطی,ترک پخشی,مدل رفتاری,مصالح بنایی,اجزای محدود}, url = {http://mcej.modares.ac.ir/article-16-10841-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-10841-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {LotfollahiYaghin1, M.A and Koohdarag2, M.}, title = {Research Note» Examination of Functions of Continuous Wavelet Transform in Identification of Crack Specification}, abstract ={Abstract Most structural failures are because of break in consisting materials. These breaks are initiated with crack extension, which is a serious threat to the behavior of structure, so different methods have been developed for distinguishing and showing such cracks. Meanwhile, the new methods based on original wavelet transform are efficient and very important in the subject of signals. The main aim of this paper is to fin the methods capable of distinguishing the specifications of cracks practically. first a modal analysis of the structure was For this purpose, performed using ANSYS software, Then the structure was analyzed as original wavelet using the wavelet toolbox of MATLAB software the results are shown in two dimensional charts of coefficient-position.}, Keywords = {Wavelets transform,Modal Analysis,signal}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی عملکرد تبدیل موجک پیوسته در شناسایی مشخصات ترک}, abstract_fa ={چکیده- بسیاری از شکست های سازه ای بهسبب گسیختگی مواد تشکیل دهنده رخ می دهند . آغاز این گسیختگی ها با ترک همراه بوده که با گسترش خود به عنوان تهدید جدی برای رفتار سازه محسوب می شود، بر این اساس روش های تشخیص و نمایان سازی ترک ، موضوع تحقیقات گسترده ای است که تا کنون انجام شده و ادامه دارد . در این میان ، روش های مبتنی بر تبدیل موجک ، از جمله روشهای جدید و کارا در مباحث سیگنال است، و اهمیت بسیار بالایی دارد. بنابراین هدف از این تحقیق، یافتن روش هایی است که توانایی شناسایی مشخصات ترک را علا وه بر تئوری ، در عمل نیز داشته باشند. تحت ANSYS بدین منظور، در این مقاله، در حالت نخست سازه با استفاده از نرم افزار المان محدود در جعبه ابزار موجک ، تحت MATLAB آنالیز مودال قرار داده شده و سپس با استفاده از نرم افزار آنالیز موجک قرار داده میشود و نتایج بهصورت نموداهای دو بعدی ضریب-موقعیت مشاهده میشود}, keywords_fa = {واژه های کلیدی: تبدیل موجک,آنالیز مودال,سیگنال}, url = {http://mcej.modares.ac.ir/article-16-6627-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6627-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Joharzadeh, ئ. and Khaji, N. and Bahreininejad3, A}, title = {Health Monitoring of Cracked Cantilever Beams Using Artificial Neural Networks Considering Nonlinear Crack Behavior}, abstract ={Abstract In this paper, using Artificial Neural Networks (ANNs) and Finite Element Method (FEM), health monitoring of damaged cantilever beams having longitudinal cracks is discussed. The main focus is devoted to the nonlinear behavior (breathing) of crack, which, to our knowledge, is taken into account in the crack detection of structures using ANNs, for the first time. Thus nonlinear behavior of crack is modeled using FEM.The changes in the natural frequencies (due to crack) of various vibration modes were implemented as input for training and testing of ANNs. By producing various scenarios for sound and damaged beams (with different damage location and severity), two specific classes of ANNs were trained to predict the location and length of longitudinal cracks. The Results showed a promising prediction for the length of cracks by the proposed methodology. Also a considerable approximation observed in the prediction of cracks location.}, Keywords = {Structural health monitoring,Cantilever beam,ANNs,Nonlinear FEM,Crack breathing}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {سلامت سنجی تیرهای طرهای شکل ترک خورده به کمک شبکه های عصبی مصنوعی، با درنظرگرفتن رفتار غیرخطی ترک}, abstract_fa ={چکیده - در این تحقیق، با بهره گیری از شبکه های عصبی مصنوعی و ر وش المان محدود، تیرهای طرهایشکل آسیب دیده که دارای ترک های طولی هستند، مورد بررسی و سلامت سنجی قرار گرفته اند . رفتار غیرخط ی ترک ها (بازوبستهشدن آنها ) در این تحقیق مورد توجه قرار گرفته است که بر اساس بررسیهای انجام شده توسط نویسندگان، در ردیا بی ترک در سازه ها به کمک شبکه های عصبی مصنوعی، رفتار مزبور تاکنون مورد توجه محققان دیگر قرار نگرفته است . بر ای منظورنمودن اثرات غیرخطی ترک، از روش المان محدود استفاده شده است . تغییرات ایجاد شده در فرکانس های طبیعی مودهای مختلف ارتعاشی در اثر وجود ترک، به عنو ان داده های لازم در آموزش و آزمایش شبکه های عصبی مورد استفاده قرار گرفته اند. با ایجاد سناریوهای مختلف برای حالات تیرهای سالم و آسیب دیده (با موقعیت ها و شدت های ترک خوردگی مختلف ) دو کلاس مشخص از شبکه های عصبی برای تعیین موقعیت و طول (شدت) ترکهای طولی در تیرها آموزش داده شده اند . نتایج حاصل از دو کلاس مزبور نشان می دهند که شبکههای آموزش دیده به صورت مطلوبی طول ترک را پیش بینی می کنند . همچنین ملاحظه می شود که پیشبینی شبکههای آموزش دیده برای تعیین محل ترک در حد قابل قبول بوده، که علل تقریبات وارده در این پیشبینی مورد بحث قرار گرفته است.}, keywords_fa = {سلامتسنجی ساز هها,تیر طره ای,شبکه عصبی مصنوعی,روش المان محدود غیرخط ی,باز و بسته شدن ترک}, url = {http://mcej.modares.ac.ir/article-16-8378-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-8378-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Mortezaei1, A.R and Zahrai, S.M}, title = {Effects of Plastic Hinge Properties in Nonlinear Analysis of Reinforced Concrete Buildings}, abstract ={Abstract Due to its simplicity, the structural engineering profession uses the nonlinear static analysis or pushover analysis. Modeling of such analysis requires the determination of the nonlinear properties of each component in the structure, quantified by strength and deformation capacities depending on the modeling assumptions. Pushover analysis is carried out for either user-defined nonlinear hinge properties or default-hinge properties, available in some programs based on the FEMA guidelines. While such documents provide the hinge properties for several ranges of detailing, the programs may implement averaged values. The user needs to be careful; becduse the misuse of default-hinge properties may lead to unreasonable displacement capacities for existing structures. This paper studies the possible differences in the results of push-over analysis due to default and user-defined nonlinear component properties. Four- and eight-story buildings were considered to represent low- and mediumrise buildings for this study. Plastic hinge length and transverse reinforcement spacing were assumed as effective parameters in the user-defined hinge properties. The observations showed that plastic hinge length and transverse reinforcement spacing have no influence on the base shear capacity, while these parameters have considerable effects on the displacement capacity of the frames. The comparisons pointed out that an increase in the amount of transverse reinforcement improves the Frames displacement capacity. Also Our findings clearly showed that the user-defined hinge model is better than the default-hinge model in reflecting the nonlinear behavior compatible with the element properties. However, although the default-hinge model is preferred due to its simplicity, the user should be aware of the circumstances provided in the program and thus should avoid the misuse of default-hinge properties.}, Keywords = {Nonlinear static analysis,Nonlinear hinge properties,Plastic hinge length,Pushover analysis,Transverse steel reinforcement}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {تأثیر انتخاب خصوصیات مفصل پلاستیک در رفتار غیرخطی قابهای بتن مسلح}, abstract_fa ={چکیده- مهندسین سازه معمولاً به دلیل سادگی از تحلیل استاتیکی غیرخطی یا تحلیل بارافزون 1 استفاده می کنند. مدلسازی برای چنین تحلیلی نیازمند تعیین خصوصیات غیرخطی هر جزء ساز ه ای است که از طریق مقاومت و ظرفیت تغییر شکل آن عضو ارزیابی شده و به فرضیات مدل سازی وابسته یا ˝ خصوصیات مفصل پلاستیک تعریف شده توسط کاربر 2 ˝ است. تحلیل بارافزون به دو صورت ˝خصوصیات مفصل پلاستیک پیش فرض 3" انجام می شود که در برخی از برنامه هایی که براساس است، موجود اند. چنین دستورالعمل هایی خصوصیات مفصل را برای محدوده ی FEMA دستورالعمل وسیعی ارائه می دهند، اما نرم افزارهای کامپیوتری مقادیر متوسطی را در نظر می گیرند . این مقاله به بررسی تفاوت های ممکن در نتایج تحلیل بارافزون ناشی از خصوصیات پیش فرض و تعریف شده توسط کاربر مؤلفه های غیرخطی می پردازد. ساختمانهای 4 و 8 طبقه که نماینده ی ساختمان های کوتاه و میان مرتبه اند برای این مطالعه در نظر گرفته شدند . طول مفصل پلاستیک و فاصله ی آرماتورهای عرضی، به عنوان پارامترهای مؤثر درخصوصیات مفاصل تعریف شده توسط کاربر فرض شد ند. بر اساس مشاهدات بهدست آمده ، طول مفصل پلاستیک و فاصلهی آرماتورهای عرضی تأثیری بر ظرفیت برش پایه ندارد در حالی که این پارامترها تأثیر قابل ملاحظه ای بر ظرفیت تغ یی رشکل قاب ها دارند . مقایسهی نتایج نشان می دهد که با افزایش مقدار آرماتورهای عرضی ، ظرفیت تغییرمکانی افزایش می یابد. نتایج به وضوح نشان می دهد که برای انعکاس رفتار غیرخطی سازگار با خصوصیات اعضا، مدل مفصل تعریف شده توسط کاربر بهتر از مدل مفصل پیش فرض است.}, keywords_fa = {کلید واژگان : تحلیل استاتیکی غیرخطی,خصوصیات مفصل غیرخطی,طول مفصل پلاستیک,تحلیل ارافزون,درصد فولاد عرضی}, url = {http://mcej.modares.ac.ir/article-16-3838-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-3838-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {.Hamdollahi, y. and fakhr, Ali and .Pahlavan, B.}, title = {Modification of non-linear model of Fahey for coarsegrained soils of Tehran, using pressuremeter tests}, abstract ={Abstract The stiffness of soils is not constant and it is highly strain dependent. Some nonlinear models such as Fahey's model for sands have been proposed for sands but these models can not be the representative of the behavior of most coarse-grained soils such as alluvial sediments of Tehran. In this paper, firstly some data of deformation modulus of several coarse-grained soils such as Tehran's soil are presented as a function of strain. Then the weakness of nonlinear models such as Fahey's model in predicting the behavior of these kind of geo-materials is presented. In next step, a new proposed model, which is in fact a type of corrected Fahey model, is explained and then a comparison is done for Tehran soil. The foundation of Milad tower is modeled using FLAC software incorporating new model and then calculated settlement is compared with measured one using micro-geodetic method.}, Keywords = {Nonlinear stiffness,Fahey's model,Shear modulus,Nonlinear behavior,Pressuremeter,Coarse-grained soils}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {اصلاح مدل غیرخطی فاهی در خاک درشت دانه با استفاده از آزمایش های پرسیومتری در آبرفت تهران}, abstract_fa ={چکیده- سختی خاک ها ثابت نیست و تابع مقدار کرنش است. تاکنون چندین مدل غیرخطی برای تغییر شکل پذیری خاک ها پیشنهاد شده است . در مقاله ی حاضر نخست ، داده هایی از مدول تغییر شکل پذیری خاک های مختلف درشت دانه از جمله خاک تهران به صورت تابع کرنش ارائه می شود . سپس ناتوانی مدل های غیرخطی مثل مدل فاهی در پیش بینی رفتار این نوع مصالح نشان داده می شود . در گام بعدی مدل جدید پیش نهاد شده در این پژوهش که در واقع نوعی مدل اصلاح شده فاهی است بیان می شود و مقایسه های لازم انجاممی شود و در انتها نشست پی برج میلاد تهران با استفاده از محاسبه می شود. در این محاسبه مدل های ساده ی خطی، مدل غیرخطی فاهی و FLAC نرم افزار همچنین مدل پیشنهادی جد ید، در نظر گرفته می شود و نشست به دست آمده از تحلیل ها با نشست اندازه گیری شده به روش میکروژئودزی مقایسه می شود. در خاتمه نتیجه گیری می شود که نحوه ی تغییر سختی خاک های درشت دانه با مدل های متداول مثل مدل فاهی سازگاری ندارد.}, keywords_fa = {کلید واژگان: سختی غیرخطی,مدل فاهی,مدول برشی,رفتار غیرخطی,پرسیومتر,خاک های درشت دانه}, url = {http://mcej.modares.ac.ir/article-16-523-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-523-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Mahmoudi, Muss}, title = {Research Note» Evaluation of the Methods of Maximum Lateral Displacement Estimation of R/C Moment Structures due to Earthquake}, abstract ={Abstract For seismic design, it is important to estimate the, maximum lateral displacement (inelastic displacement) of the structures due to earthquakes for several reasons. Seismic design provisions estimate the maximum roof and storey drifts occurring in major earthquakes by amplifying the roof displacement and drifts of the structures obtained by elastic analysis subjected to seismic design load, with a coefficient named “displacement amplification factor” which is greater than one. Here, this coefficient depends on various parameters such as ductility factor and overstrength factor. The present research aims to evaluate the value of the displacement amplification factor in seismic design codes and then tries to propose a new value as displacement amplification factor to estimate the maximum lateral structural displacement due to severe earthquakes. In seismic codes, since the displacement amplification factor is related to “force reduction factor”, hence; this aspect has been accepted in the current study. Meanwhile, two methodologies were applied to evaluate the value of displacement amplification factor and its relation with the force reduction factor. In the first methodology, which is applied for all structures, the ratio of displacement amplification and force reduction factors was determined directly. Whereas, in the second methodology that is applicable just for the R/C moment resisting frames, the ratio was obtained by calculating both factors, separately. The results were alike and both of them could estimate the ratio of the two factors from 1 to 1.2. The results also indicated that the ratio of the displacement amplification factor and the force reduction factor differs to those proposed by seismic provisions such as NEHRP, IBC and Iranian seismic code (Standard no. 2800).}, Keywords = {Displacement amplification factor,Force reduction factor,Maximum lateral displacement,Ductility factor}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {ارزیابی روشهای تخمین تغییرمکان جانبی واقعی ساختمانهای بتنی در برابر زلزله}, abstract_fa ={چکیده- در طراحی لرزه ای سازهها، محاسبهی تغییر مکان جانبی بیشینهی سازهها اهمیت زیادی دارد. آئیننامههای طراحی لرزه ای، تغییرمکان جانبی بیشینهی سازهها را در برابر زلزله های شدید، با ضرب تغییر مکان جانبی نظیر طراحی آنها، در ضریبی به نام ضریب بزرگ نمایی تغییرمکان تعیین می - کند. هدف اصلی این مقاله ، بررسی ضریب بزرگنمایی تغییرمکان پیشنهادی در آییننامه های طراحی لرزهای و تعیین نسبت آن به مقدار ضریب رفتار است. برای رسیدن به این هدف از دو روش استفاده شده است . در روش اول که برای تمامی انواع سازهها کاربرد دارد، نسبت ضریب بزرگ نمایی تغییرمکان و ضریب رفتار مستقیماً تعیین شد. در روش دوم که فقط برای قاب های خمشی بتن مسلح تحقیق شده است، هر یک از ضرایب بزرگنما یی تغییرمکان و رفتار به طور جداگانه محاسبه شده و سپس ، نسبت آنها تعیین شده است . نتایج حاصل از هر دو روش حاکی از این مطلب است ک ه مقدار نسبت ضریب بزرگنمایی تغییرمکان و ضریب رفتار در آیینامههای طراحی لرزه ای، کوچک تر از مقادیر واقعی است و بهتر است در مورد آنها تجدید نظر قرار شود.}, keywords_fa = {ضریب رفتار,کلید واژگان: تغییرمکان جانبی بیشینه,ضریب بزرگن مایی تغییر مکان,زمان تناوب اصلی,زلزلههای شدید و ضریب شکلپذیری}, url = {http://mcej.modares.ac.ir/article-16-8107-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-8107-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {DardaeiJoghan1, S. and DANASHJO, F}, title = {The Values of Damage Indices in Unreinforced and Flange-Plate Connections of Steel Moment Frames under Earthquake Loads}, abstract ={Abstract Studying the response details of steel moment connections is very important due to the role of connections in moment resisting frames. The aims of this research were: i) to study the damage indices of steel material including: Pressure Index, Mises Index, Equivalent Plastic Strain Index, Triaxiality Index, and Rupture Index and ii) to compare these indices at connections of steel moment frames under earthquake loads. To achieve this, time history nonlinear dynamic analysis is performed using selected earthquake records on 2D model of special steel frame with ten storey and one bay to determine maximum rotations of connections. Then, damages indices of the selected connections under maximum rotation of records are investigated with selecting two types of moment connections. The results indicate that damage indices are dependent on type of connection, location of surveying, and rotations caused by earthquake movements. This dependency is very considerable for Equivalent Plastic Strain Index and Ruptureindices}, Keywords = {Nonlinear Dynamic Analysis,Moment frames,connection,Damage indices}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {مقادیر شاخص های خسارت دراتصالات مستقیم و با ورق اتصال بال در قاب های فولادی تحت اثر زلزله}, abstract_fa ={چکیده - بررسی جزئیات رفتاری اتصالات با توجه به نقش آن ها در سیستم های قاب خمشی، دارای اهمیت خ اصی است . در این مقاله ضمن معرفی شاخص های خسارت ، شامل شاخص های فشار، میسز، کرنش پلاستیک معادل، سه محوره و گسیختگی، به استخراج و مقایسه ی این شاخص ها در اتصالات خمشی فولادی تحت اثر نیروی زلزله پرداخته می شود. بدین منظور با انجام آنالیز دینامیکی ،Imperial Valley طبس و ،Duzce تاریخچهی زمانی غیرخطی با استفاده از رکوردهای زلزله های برای مدل دو بعدی یک قاب فولادی ویژه با ده طبقه و یک دهانه، میزان بیشینه ی دوران در اتصالات استخراج میشود. سپس با انتخاب دو نوع اتصال خمشی ، شامل اتصال مستقیم تیر به ستون و اتصال با ورق اتصال بال، شاخص های خسارت اتصالات برای دوران های حاصل از زلزله های منتخب بررسی و مقایسه می شود. نتایج حاصل از تحقیق نشان می دهد با تغییر نوع اتصال، محل مورد بررسی و یا نوع زلزله، مقادیر شاخصهای خسارت و در نتیجه پتانسیل آسیب تغییر می نماید . این تغییرات در شاخصهای کرنش پلاستیک معادل و گسیختگی مشخص تر می باشد.}, keywords_fa = {کلید واژگان : آنالیز دینامیکی تاریخچه ی زمانی غیرخطی,اتصالات,قاب های خمشی,شاخ صهای خسار ت اتصالات}, url = {http://mcej.modares.ac.ir/article-16-12219-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-12219-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Shahverdiani, K. and Rahai, Ali.R}, title = {Effect of Time Dependent Deformations of Concrete on Prestressing Force in Cylindrical Tank\'s shells}, abstract ={Abstract Prestressing techniques are generally used for the construction of large containment shells to overcome tension and to ensure tightness. Thus, the evaluation of the prestressing force variations considering the geometry and mechanical characteristics of tendons becomes an important matter. This paper considers the effects of time dependent deformations of materials on the circumferential prestress force in prestressed concrete cylindrical containments. Numerical studies are performed using creep and relaxation models presented in different codes of practice after checking the numerical model by experimental data reported elsewhere about a prestressed concrete beam. The effects of vertical prestressing and wall thickness are also studied. Obtained results show an amount of 15% to 22% of prestress loss in tendons, specially in those located around wall’s mid-height , on which relaxation of steel has a dominant effect. Furthermore, the minor effect of vertical prestresssing might be mentioned. Besides, the creep model of Iranian concrete code is studied and some suggestions are made for the modification of the coefficient used for the prestress losses due to relaxation effects.}, Keywords = {Keywords :Prestress loss,Cylindrical tank,Concrete creep,Steel relaxation}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {اثر تغییر شکل های تابع زمان بتن بر نیروی پیش تنیدگی در مخازن استوانه ای}, abstract_fa ={چکیده- در مخازن حجیم بتنی برای غلبه بر کششهای ایجاد شده در جدار و جلوگیری از ترک- خوردگی، از تکنیک پیشتنیدگی استفاده میشود. در این ارتباط، مسئلهی برآورد افتهای احتمالی نیروی پیشتنیدگی، با توجه به مشخصات مسیر و هندسهی کابلها، اولویت خاصی دارد. در مقالهی حاضر، با مدل سازی عددی به روش اجزاء محدود و استفاده از مدلهای مختلف برای وارفتگی بتن و وادادگی فولاد، تغییرات نیروی پیشتنیدگی محیطی، در جدار استوانهای شکل مخازن بتن پیشتنیده، بررسی شده است. سنجش اعتبار مدل عددی نیز با دادههای تجربی موجود از آزمایش یک تیر پیش- تنیده انجام شده است. در این راستا، اثر پیشتنیدگی قائم و ضخامت جدار، مطالعه شده و مدلهای مختلف وارفتگی بتن با هم مقایسه شدهاند. نتایج حاصل، بروز افت 15 تا 22 درصدی را پس از حدود 13 سال نشان میدهد که در آن نقش وادادگی فولاد اهمیت بیشتری دارد. با مدل وارفتگی پیشنهادی برای آییننامهی بتن ایران، افتی در حد میانگین دو مقدار مذکور نتیجه میشود. بر این اساس، در محاسبهی مجموع افتهای نیروی پیشتنیدگی، اعمال ضریب جدیدی بر افت حاصل از وارفتگی فولاد توصیه شده است.}, keywords_fa = {کلید واژگان: افت پیشتنیدگی,مخزن استوانهای,وارفتگی بتن,وادادگی فولاد}, url = {http://mcej.modares.ac.ir/article-16-6472-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6472-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Yazdani, M. and Paseh2, H.R and Masjoodi, M.}, title = {Numerical Analysis of Dynamic Pore Water Pressure in Earth Dams under the Earthquake Loading}, abstract ={Abstract In this study, the dynamic behaviour and pore water pressure generation in a typical earth dam were investigated using the non-linear dynamic analyses results. Based on the Byrne version of the Finn’s Model, variations of pore water pressure ratio against the strength parameters of materials and also the dilatancy angle of shell material were considered. In addition, using the scaling method of applying maximum acceleration, the variations of pore water pressure ratio and liquefaction phenomenon were investigated in different maximum accelerations. The results demonstrated that excess pore pressure depends strongly on the strength parameters, dilatancy angle of materials and applied maximum acceleration. Inappropriate compaction of shell material results in severe increase in liquefaction-induced failure potential. In earth dams with appropriate compaction of materials, liquefaction probability in the dam body, is negligible even in large earthquake accelerations.}, Keywords = {Angle of dilatancy,Dynamic Analysis,earth dam,Excess pore water pressure,Liquefaction}, volume = {10}, Number = {3}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {تحلیل عددی فشار آب منفذی دینامیکی در سدهای خاکی تحت بارگذاری زلزله}, abstract_fa ={چکیده- در این مقاله، رفتار دینامیکی و تولید فشار آب حفره ای اضافی در سد خاکی نمونه، با استفاده از نتایج تحلیلهای دینامیکی غیرخطی و با در نظر گرفتن فشار آب حفره ای اضافی تولید شده در مدت زلزله، بررسی شده است. بر پایه نسخه بایرن 1 از مدل فین 2، تغییرات نسبت فشار آب حفره ای اضافی در برابر تغییرات پارامترهای مقاومتی اجزای سد و نیز در برابر رفتار اتساعی یا انقباضی مصالح پوسته، که امکان رخداد روانگرایی در آنها ملحوظ شده- مطالعه شده است. همچنین با استفاده از روش مقیاس کردن بیشینه شتاب اعمالی، تغییرات نسبت فشار آب حفره ای اضافی و پدیده روانگرایی در شتابهای بیشینه متفاوت، بررسی شده است. نتایج حاصل، وابستگی پاسخ فشار آب حفره ای را به پارامترهای مقاومتی اجزای سد، زاویه اتساع مصالح و شتاب اعمالی بیشینه نشان می دهد و اینکه در صورت نبود تراکم مناسب در مصالح پوسته، پتانسیل گسیختگی بر اثر روانگرایی بهشدت افزایش می یابد. نتایج همچنین نشان میدهد که در سدهای خاکی ساخته شده با تراکم مناسب مصالح، احتمال وقوع روانگرایی حتی در زلزلههای با دامنه شتاب بسیار زیاد، ناچیز است.}, keywords_fa = {کلید واژگان: تحلیل دینامیکی,روانگرایی,زاویه اتساع,سد خاکی,فشار آب حفره ای اضافی}, url = {http://mcej.modares.ac.ir/article-16-881-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-881-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {SalehiD., Iman and SoltaniM., Masoud and Tasnimi, Abaas Ali}, title = {Linear Homogenization of Brick Masonry Stuctures}, abstract ={bstract The average behavior of composite material like masonry can be described in terms of the relation average stresses and strains (macro model) if the material is assumed to be homogeneous. The average stress-strain relationship can be determined generally using two approaches. A possible approach is experimental investigation from the available experimental data. Another approach, adopted in this resedrch, is to develop a linear homogenization technique, which describes the behavior of the masonry from the geometry and the behavior of the representative basic cell. In this research, the elastic properties of a basic cell in masonry with a periodic arrangement of blocks were obtained based on a local stress field approach (micro-modeling of the mortar and blocks).Two different methods were used for computing the equivalent orthotropic elastic properties of the basic cell as a continuum, the approximate energy method (a closed form solution) and the finite element based method. The finite element method was used to approximately find the orthotropic yield curves of the homogenous element. The similarity of the general behavior of these gied curves with regard to the experimental facts was considerable.}, Keywords = {Masonry,Linear homogenization,Finite Element,Approximate method,stress,Yield curves}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {همگن سازی خطی در سازه های بنّایی}, abstract_fa ={چکیده- در این مقاله همگنسازی خطی در سازههای بنایی با پیکربندی متناوب مطالعه شده است. بدین ترتیب که المان پایه بهعنوان کوچکترین جزء تکرار شونده با ریزمدلسازی ملات و واحد بنایی و تخصیص خواص ارتجاعی و خطی به آن دو، با المانی همگن و ارتوتروپ معادل سازی میشود. پارامترهای ارتوتروپ به دو روش المان محدود و روش تقریبی انرژی (با حل بسته) تعیین شده و نیز در روش المان محدود با تعریف ماتریس انتقال، تنش همگن به تنشهای ناهمگن المان پایه انتقال می یابد و در مقایسه با مدل ناهمگن دقت این دو فرایند به اثبات میرسد. همچنین با تهیه یک برنامه المان محدود، منحنیهای تسلیم المان همگن معادل با فرض رفتار خطی– شکننده و معیارهای تسلیم مناسب برای ملات و واحد بنایی، ارائه و مطالعه می شود. شباهت رفتار کلی این منحنیهای تسلیم با منحنیهای تسلیم آزمایشگاهی قابل توجه است.}, keywords_fa = {کلید واژگان: سازه بنایی,همگنسازی خطی,المان محدود,روش تقریبی,پیشبینی تنش,منحنی تسلیم}, url = {http://mcej.modares.ac.ir/article-16-4202-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4202-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Mahmoodi1, H.D.N., and FaroghHossieini, M. and Ahmadi, M. and .Jalali, m.s}, title = {Stydying the effect of weight on Time- Dependent Behavior of Gotvand dam Foundation}, abstract ={Abstract Gotvand rock fill dam is being constrcted on Karun river located in Khoozestan province south of Iran. The dam is foung on Aghagari formation which is consisted of mudstone and sandstone layers. These layers are intermittent of weak to medium strength with uniaxial compressive strength 15 and 25 MPa respectibely. Some regional factors as continuous unloading caused by river flood washed off and horizontal tectonic loading have created a local anticline in the foundation of dam. According to previous analyses, results have shown that this folding will continue over the time. In this research effect of the dam weight on time d- dependant deformation of the dam foundation has been studied. Ration of horizontal to vertical stresses (K) was estimated to be 0.4 to 0.7 by in-situ tests, so dam site numerical models were executed (numerical analysis wity the FLAC3D code) with K equal to 0.4,0.55 and 0.7. First, the models were executed statically. Maximun settlement of foundation due to the dam weight was estimated a bout 37cm. Ihen for time dependent analysis, the behavior of rocks is assumed to obeay Maxwell creep viscousplastic rheological model and the models were executed for 100 years equal to the dam life time. The results of numerical analysis show that upward deformations of the foundation with K=0.55 and 0.7 is continuously, even in the central region of dam where the dam weight is maximum. But in the model with K=0.4, in the first 60 years after the construction, creep deformation are downward and after this time, directions of deformation were changed to upward.}, Keywords = {Gotand dam,creep,Time- Dependent,analysis,Dam foundation,Numerical}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی تأثیر وزن سد بر رفتار وابسته به زمان پی ساختگاه سد گتوند}, abstract_fa ={چکیده - سد گتوند از نوع سنگریزهای بوده و در استان خوزستان روی رودخانه کارون در حال ساخت میباشد. پی سد در سازند آغاجاری قرار خواهد گرفت که شامل ماسه سنگ و گلسنگ بوده که به صورت تناوبی روی هم قرار گرفتهاند. مقاومت تکمحوره سنگهای مذکور به ترتیب برابر 15 و 25 مگاپاسکال است یعنی جزو سنگهای ضعیف و متوسط محسوب می شوند. عواملی مانند باربرداری مداوم روباره حاصل از فرسایش بر اثر جریان رودخانه و همچنین بارهای افقی تکتونیکی در منطقه، تاقدیسی محلی را در پی و ساختگاه سد ایجاد کرده است. با توجه به تحلیل ها مشخصشد که روند تاقدیسی شدن ادامه دارد. در این تحقیق به بررسی تأثیر وزن سد بر تغییرشکلهای وابسته به زمان در پی سد پرداخته شده است. با توجه به دادههای آزمایشهای انجام شده در منطقه که نسبت تنش 0 ارائه کرده، تحلیل عددی ساختگاه سد با نسبت تنشهای افقی /4 -0/ را برابر 7 (k) افقی به عمودی 0 انجام شد. ابتدا مدلها در حالت استاتیکی اجرا و نشست حاصل از ساخت / 0و 7 /55 ،0/ به عمودی 4 سد تعیین شد. مقدار بیشینه نشست برابر 37 سانتی متر بدست آمد. پس از این مرحله، رفتار سنگهای پی ویسکوپلاستیک ماکسول در نظر گرفته شد و مدل برای 100 سال - برابر با عمر بهرهبرداری سد- اجرا شد. نتایج تحلیل عددی حاکی آن است که روند بالازدگی نقاط سطح پی حتی در نقاط مرکزی - 0 در طول زمان / 0 و 7 / که بیشینه وزن سد روی آن قرار دارد- در نسبتهای تنش افقی به عمودی 55 0 در نقاط مرکزی، در 60 سال ابتدایی ساخت سد جابجاییهای خزشی رو / ادامه دارد؛ اما در مقدار 4 به پایین ایجاد شده و پس از آن تغییرشکلها به سمت بالا تغییر جهت خواهند داد.}, keywords_fa = {تحلیل عددی,.FLAC3D کلید واژگان: سد گتوند,خزش,تحلیل وابسته به زمان,پی سد,نرمافزار .FLAC3D}, url = {http://mcej.modares.ac.ir/article-16-6522-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6522-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Kavussi1, Amir and Abdi, Ali}, title = {Evaluation of Stripping in Asphalt Pavements Using Abrasion Test}, abstract ={Abstract The main purpose of this research is studying stripping of asphalt mixtures. Key factors were the aggregate properties and the suitable methods to control and assess the stripping distress in laboratory conditions. Our case study was the "Zanjan-Qazvin" freeway in which this distress is manifested extensively. The aggregates for the tests were selected from the sections in which stripping were more serius. stripping was found to be caused by excess values of siliceous minerals. This resul were obtained using XRF & XRD analyses. Primary estimation of stripping was determined using boiling test over the loose mix specimens. Specimens were tested under theWTAT. Hydrated lime was utilized as the antistripping agent. It is concluded that if hydrated lime is utilized as an additives, not only stripping is reduced but also the stability and durability of the asphalt pavement is increased. The presented approach ultimately resulted in improving mix properties.}, Keywords = {Stripping,Moisture Damage,Asphalt Pavement,Antistripping Additives and Hydrated Lime}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی عریانشدگی مصالحسنگی در رویههای آسفالتی به روش آزمایش سایش}, abstract_fa ={چکیده- هدف از این تحقیق بررسی عریانشدگی در رویههای آسفالتی، با تکیه بیشتر بر مصالح سنگی و انتخاب روشی مناسب برای کنترل و بررسی این معضل در شرایط آزمایشگاهی است. برای بررسی این خرابی با مطالعه موردی آزادراه زنجان قزوین که این پدیده در برخی از قطعات آن دیده شده، از معدن مصالح سنگی مربوط به قطعاتی که عریان شدگی در آنها شدیدتر از سایر قسمتها بود، استعداد عریانشدگی XRD و XRF مصالح برای ساخت آسفالت انتخاب شد. در ابتدا با آزمایشهای این مصالح ناشی از فزونی کانی سیلیس در آنها مشخصشد. سپس با ساخت نمونههای مخلوط قیر و مصالح و انجام آزمایش بصری آبجوشان بر روی این نمونهها تخمین اولیهای از عریانشدگی مصالح سنگی در مخلوطهای آسفالتی بهدست آمد. همچنین با ساخت نمونههای آسفالت سطحی و انجام آزمایش سایش در شرایط مرطوب بر روی نمونهها، صحت آزمایشهای انجامشده قبلی از دیدگاه دیگری بررسی شد. در تمامی آزمایشهای انجام شده بر روی نمونههای آسفالتی از ماده افزودنی آهک هیدراته برای ترمیم و کاهش این خرابی استفاده شد. نتایج حاصل از این تحقیق حاکی از آن است که اگر آهک هیدراته بهعنوان افزودنی بهکار رود موجب تقلیل عریان شدگیشده و باعث افزایش انسجام و دوام روسازی آسفالتی میشود. رویکرد ارائهشده به بهبود و اصلاح خواص مصالح مورد استفاده در رویههایآسفالتی در برابر عریانشدگی منجر میشود.}, keywords_fa = {کلید واژگان: عریانشدگی,برهنگی مصالح,آسیبدیدگی رطوبتی,آزمایش سایش در شرایط مرطوب,افزودنی ضدعریانشدگی,آهک هیدراته}, url = {http://mcej.modares.ac.ir/article-16-7037-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-7037-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Salmanpour, A.H. and Arbabi, F.}, title = {Study of Seismic Behavior of Buckling Restrained Braced Frames}, abstract ={Abstract This work aimed to identify the seismic behavior of buckling restrained braced frames (BRBFs). A six-story frame with buckling restrained braces was analyzed at different hazard levels. After the discussion of some aspects of BRBs, the results of detailed nonlinear dynamic analyses are examined to characterize the seismic behavior of the model building. Also the effect of near-field ground motions on the behavior of the model was studied. The results indicate that BRBFs behave quite well under seismic loads. However, there are some concerns about the performance of this system under more frequent lower intensity ground motions.}, Keywords = {Keywords}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {مطالعه رفتار لرزهای قابهای مهاربندی شده کمانش ناپذیر}, abstract_fa ={چکیده - در این مقاله رفتار لرزهای نمونه سازه مهاربندی شده کمانشناپذیر شش طبقه در سطوح مختلف خطر با استفاده از تحلیل دینامیکی غیرخطی مطالعه میشود. نخست این مهاربندها به اختصار معرفی و مزایا و معایب آنها مرور می گردد . سپس به مسائلی نظیر نیاز لرزهای قابهای مهاربندی شده کمانش ناپذیر در سطوح مختلف خطر و نحوه توزیع آن در سازه، ارزیابی مقدماتی عملکرد لرزهای قابهای مهاربندی شده کمانش ناپذیر، اثر زمین لرزه حوزه نزدیک بر رفتار لرزهای قاب مهاربندی شده کمانش ناپذیر میپردازیم. نتایج این مطالعه نشان میدهد که قابهای مهاربندی شده کمانش ناپذیر عموماً عملکرد لرزهای بسیار مطلوبی دارند؛ هرچند نگرانیهایی در باره عملکرد آنها در زمینلرزههای کوچک و متوسط وجود دارد.}, keywords_fa = {کلید واژگان: مهاربندهای کمانشتاب,قابهای مهاربندی شده کمانشنناپذیر,رفتار لرزهای,زلزلههای حوزه نزدیک}, url = {http://mcej.modares.ac.ir/article-16-3285-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-3285-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {IzadiZamanAbadi1, E. and .Nateghi-Alahi, F. and Motamedi, M.}, title = {Comparison of Accordion Metallic Dampers with Filled Accordion Metallic Dampers Using Polymeric Foam under Axial Cyclic Loading}, abstract ={During the last decades, many researches have been carried out on development of supplemental passive energy absorption devices especially hysteretic metallic dampers and different types of them with different capacities and potentials have been developed. The idea of buckling of thin-walled tubes and the use of this property was led to develop an accordion metallic damper (AMD) [Motamedi, Nateghi-Alahi-2007]. This damper utilizes the capability of accordion thin-walled tube for excitation of axisymmetric concertina buckling mode as a damping mechanism which in turn increases the amount of dissipated energy. In this paper filled accordion metallic damper (FAMD) is suggested and analytically and experimentally the behavior of AMD's and FAMD's under axial cyclic loading are investigated and compared. For this purpose, Firstly analytical studies based on Finite element method and nonlinear dynamic analysis was performed on FAMD's for the determination of the approximate preliminary specifications of different polymers for potential use. After specifying the preliminary material properties, 4 specimens include 2 FAMD's filled by polymeric foam and 2 AMD's were subjected to dynamic tension and compression actuator and the effect of filling AMD's by this polymeric foam on the some of important specifications of damper studied and try to use this method for improving and developing of AMD's. Based on the results obtained using the appropriate filling inside the AMD's is a suitable technique for the purpose of improvement the some of important specifications such as the number of cycles before failure, amount of dissipated energy and plastic capacity. The effect of interaction between foam and accordion thin walled tubes play an important role for this purpose especially in low capacity AMD's.}, Keywords = {Experimental Study,Filled Accordion Metallic Damper,Polymeric Foam}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {مقایسهی شاخصهای رفتار میراگر فلزی آکاردئونی توخالی و پر شده با فوم پلیمری در بارگذاری محوری رفتو برگشتی}, abstract_fa ={چکیده- در چند دهه گذشته تحقیقات بسیاری در زمینه قطعات الحاقی مستهلک کننده انرژی به ویژه میراگرهای فلزی پسماند انجام شده و نمونههای متنوعی از آن با قابلیتهای مختلف توسعه یافته است. درسالیان اخیر استفاده از کمانش آکاردئونی سیستمهای جدار نازک لولهای نظر پژوهشگران را جلب کرده و به توسعهی میراگر فلزی آکاردئونی منجر شده است. در این مقاله پساز معرفی میراگر فلزی آکاردئونی پر شده، شاخصهای رفتار میراگر پر شده و توخالی برای بارگذاری محوری چرخهای مطالعه و مقایسه شده است. بدین منظور ابتدا به روشی تحلیلی اجزای محدود، مشخصات تقریبی پلیمر پرکننده مؤثر تعیین و سپس چهار نمونه آزمایشگاهی شامل دو نمونه میراگر پر شده با نوع خاصی فوم پلیمریک و دو نمونهی میراگر توخالی متناظر با آنها، با استفاده از جک هیدرولیکی کشش و فشار آزمایش شده است. سپس تأثیر پرشوندگی میراگر با فوم بر برخی از مهمترین شاخصهای رفتار تعیین و سعی شده از این روش بهمنظور پایداری و بهبود رفتار میراگر استفاده شود. این مطالعه نشان میدهد که استفاده از ماده پرکننده متناسب در داخل میراگر، روشی مناسب بهمنظور افزایش برخی شاخصهای رفتاری میراگر مانند تعداد چرخهی قابل تحمل، میزان جذب انرژی و همچنین ظرفیت خمیری کشش و فشار میراگر بوده و اثر اندرکنش بین فوم و جدار آکاردئونی در افزایش جذب انرژی و افزایش ظرفیت خمیری سیستم بهویژه برای نمونههای جدار نازک آکاردئونی با ظرفیت باربری پایین، چشمگیر است.}, keywords_fa = {کلید واژگان: مطالعه آزمایشگاهی,میراگر فلزی آکاردئونی پر شده,فوم پلیمریک}, url = {http://mcej.modares.ac.ir/article-16-921-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-921-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Maosavi,, S.K. and Ghodsian,, M.}, title = {Expermental Investigation on the Effect of Relative Channel Radius on bed scour in a 90 degree}, abstract ={Abstract The problem of scour and variations of bed topography, which is influenced by different parameters is very important in river engineering. In order to study the influence of discharge, relative flow depth and relative channel radius on dimensions of scour hole, experiments were conducted. The results are given in this paper.}, Keywords = {bed Scour,90 Degree Bend,Dimensional analysis,Scour Width,Scour Depth and Scour Length}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی آزمایشگاهی تاثیر انحنای نسبی کانال بر آبشستگی بستر در خم 90 درجه}, abstract_fa ={چکیده- بیشتر رودخانهها تمایل به مارپیچی شدن و فرسایش ساحل خارجی خود را در محل قوسها دارند. بهمنظور حفظ پایداری سواحل رودخانهها میتوان از روشهای ساماندهی رودخانه استفاده کرد. یکی از مسائل قابل توجه در مهندسی رودخانه، آبشستگی و تغییرات توپوگرافی بستر رودخانه در محل قوس است. پارامترهای مختلفی بر این پدیده مؤثرند. در این تحقیق برای شناسایی و بررسی تأثیر پارامترهای دبی جریان، عمق نسبی جریان و انحنای نسبی کانال بر ابعاد حفره آبشستگی، آزمایشهایی طراحی و اجرا شد که نتایج بهدست آمده، ارائه میشود.}, keywords_fa = {کلید واژگان: خم 90 درجه,توپوگرافی بستر,عمق آبشستگی,طول آبشستگی و عرض آبشستگی}, url = {http://mcej.modares.ac.ir/article-16-11637-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-11637-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Soroush, Abbas and Tabarsaz, Saeedeh}, title = {Numerical Analysis of Ground Reinforced with a Stone Column Group}, abstract ={154 Abstract Numerical Analysis of Ground Reinforced with a Stone Column Group Saeedeh Tabarsaz and Abbas Soroush School of Civil and Environmental Engineering, Amirkabir University of Technology, Tehran, Iran soroush@aut.ac.ir Abstract This paper presents the numerical analyses of a group of stone columns penetrated in a 10 m deep soft clay stratum. A rigid raft transfers the super-structure's loading to the stone columns and the parent ground. The columns group comprises of five columns with a symmetric configuration. The numerical analyses are performed on a plane strain idealization of the structure, using an elasto plastic constitutive behavior for both the stone columns and the soft clay layer. Additional numerical analyses with different range of parameter, like number of columns, space of columns, column’s length, foundation’s size, Poison ratio of soil and stone columns’ material and modulus of elasticity ratio of the stone columns’ material were conducted. The results of analyses showed that lateral displacements (bulging) occur in the upper parts of the columns (between 2D and 4D from the top; D is the column diameter) and the lateral displacements are comparatively higher for the side columns. The major result of the analyses is that for a group of stone columns supporting a rigid raft under spread loading, the lengths of the stone columns could be designed unequal, i.e., inside the columns can be shorter, without significantly increasing of the settlements of the column group.}, Keywords = {Stone columns,soft soils,Numerical analyses,Ground improvement}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {تحلیل عددی رفتار زمین مسلح شده با گروه ستون سنگی}, abstract_fa ={چکیده- در مقاله حاضر تحلیل عددی گروه ستون سنگی 1 با طول ده متر ارائه شده که در لایه ای رسی ساخته شدهاند. بارگذاری توسط پی صلب انجام شده است. گروه ستونهای سنگی شامل پنج ستون سنگی می شود که هندسه خاک و ستونها متقارن است. تحلیلهای عددی انجام شده به صورت دوبعدی و کرنشصفحهای است. رفتار مصالح ستون سنگی و خاک اطراف آن با مدل رفتاری الاستوپلاستیک مور- کولمب مدل سازی شده است. در تحلیلهای انجام شده اثر پارامترهای مختلف مانند تعداد ستونها، فاصله ستونها از یکدیگر، طول ستونها، نسبت مدول الاستیسیته مصالح ستون سنگی به مدول الاستیسیته خاک اطراف، اندازه پی و ضریب پواسون مصالح ستون و خاک مطالعه شده اند. نتایج نشان میدهند که شکم دادگی ستون که به گسیختگی آن منجر میشود، در قسمتهای بالایی ستون (بین دو تا چهار برابر قطر ستون از سر ستون) اتفاق میافتد. شکم دادگی در ستونهای داخلی در بخشهای پایینتری نسبت به ستونهای کناری اتفاق میافتد. مهمترین نتیجه بهدست آمده این است که گروه ستون سنگی میتوانند شامل ستونهایی با طول غیر یکسان باشند که ضمن صرفه اقتصادی، هدف از ساخت ستونهای سنگی را در کاهش نشست تأمین کنند.}, keywords_fa = {کلید واژگان: ستونهای سنگی,خاک سست,تحلیل عددی,بهسازی خاک}, url = {http://mcej.modares.ac.ir/article-16-9308-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-9308-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Ouhadi1, V.R. and Choobchian, S. I.}, title = {Geo-Environmental Behaviour of Montmorillonite Treated with Cations in Retention of Pb}, abstract ={The behauiours of clay minerals and the extent of clay-heavy metals interactions are functions of CEC and the exposed SSA of the clay minerals. The type and the quantity of double layer cations have an essential impact on this process. This work aimed to investigate the behaviour of Na-montmorillonite and Ca-montmorillonite in interaction with Pb as a heavy metal ion. The results showed that although the buffering capacity pattern of montmorillonite and different concentrations of NaCl is relatively similar, the contaminant retention property of montmorillonite is a function of the quantity of sodium ions with which the soil is treated. In Ca-montmorillonite, in spite of very small change in its buffering capacity in comparison with that of montmorillonite, a noticeable change in contaminant retention was observed. This emphasizes the limitation of buffering capacity experiment to determine the extent of soil-contaminant interaction. On the other hand, retention experiment was able to differentiate between the behaviour of these two samples. Finally, the results of the interaction process of sodium- and calcium- montmorillonite with heavy metal contaminant were compared using the XRD experiments.}, Keywords = {Montmorillonite,Double layer,Heavy Metal Contaminant,XRD experiment}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {رفتار ژئوتکنیک زیست محیطی مونت موریلونیت اصلاح شده با کاتیون در جذب آلاینده سرب}, abstract_fa ={چکیده- از آنجا که رفتار خاکهای رسی و میزان اندرکنش آنها با آلایندهها تابعی از ظرفیت تبادل و سطح مخصوص فعال آنها است، نوع ساختار خاک و کاتیونهای موجود در لایه (CEC) کاتیونی دوگانه، نقش عمدهای را در فرایند اندرکنش کانیهای رسی با آلایندههای زیستمحیطی ایفاء میکنند. بیشترین سهم کانیهای رسی مورد استفاده در مراکز دفن مهندسی زباله را سدیم- مونتموریلونیت و کلسیم- مونتموریلونیت تشکیل میدهد. در این مقاله تأثیر نوع کاتیون لایه دوگانه بر جذب آلاینده سرب در کانی رسی مونتموریلونیت بررسی شده است. بدین منظور نمونههای مختلف رسی سدیم- تهیه CaCl و 2 NaCl مونتموریلونیت و کلسیم-مونتموریلونیت با استفاده از غلظتهای متفاوت نمک شده و رفتار آنها در اندرکنش با سرب مطالعه شده است. نتایج تحقیق نشان میدهد که اگرچه تغییرات نسبت به هم تغییر ،NaCl ظرفیت بافر کردن نمونه مونتموریلونیت در غلظتهای متفاوت نمک تا غلظتی معادل حداکثر NaCl ناچیزی دارد، اما میزان نگهداری سرب توسط نمونههای حاوی و سطح مخصوص فعال) افزایش یافته و پس از آن کاهش CEC پراکندگی خاک (نقطه حداکثر مییابد. به بیانی دیگر، آزمایش تعیین میزان آلودگی جذب شده توسط خاک، حد آشکارسازی قابل- توجهتری نسبت به آزمایش تعیین بافر کردن خاک دارد. در حالت مونتموریلونیت هومویونی شده با علیرغم کاهش غیر قابل ملاحظهی ظرفیت بافر کردن نسبت به مونتموریلونیت خالص، میزان ،Ca کمتری از نگهداری سرب در آن نسبت به مونتموریلونیت خالصو سدیم-مونتموریلونیت مشاهده شد. این موضوع نیز علاوه بر نشان دادن محدودیت آزمایش بافرکردن، بیانگر تأثیر نوع ساختار و کاتیون موجود بر قابلیت نگهداری آلودگی در خاک است. نتایج فرایند اندرکنش نمونههای سدیم نیز XRD مونتموریلونیت و کلسیم مونتموریلونیت با آلاینده فلز سنگین بهکمک آزمایشهای مقایسه شده است.}, keywords_fa = {آلاینده فلز سنگین,XRD کلید واژگان: مونت موریلونیت,لایه دوگانه,آزمایش}, url = {http://mcej.modares.ac.ir/article-16-4669-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4669-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Gerami, M. and GhaznaviOskuei, A.}, title = {Retrofit of Typical Rigid Steel Connection Using Reduced Beam Flange Section}, abstract ={Abstract The moment connections sustained by many steel buildings were damaged during the recent earthquakes due to brittle fractures in the special moment resistant frames. Previous studies showed that although the top beam flange resisted due to the interaction of concrete slab, many damages are created because of weld cracking between the bottom beam flange and the column flange. Different methods of retrofit and rehabilitation could be used to prevent weld cracking and brittle fracture of the joints. The reduction of the bottom flanges of steel beams near the beam-column joints in the special moment resistant frames is currently an acceptable alteration of a connection because the top flange is located in the concrete slab and removing of concrete slab has financial and technical problems. RBS connection is one of the different kinds of Post-Northridge connections in which by cutting some parts of the flange near the end of the beam (where the possibility of making plastic hinges is high), the plastic hinge moves by the side of the column into the area within the beam. By using this method, the connection is altered from the special moment frame into a more ductile connection that has more ability to endure in plastic rotation, and generally ductility increases. The ductility of the panel zone is one of the parameters, which undoubtedly affects the manner of the yield of beams with RBS connection. Our findings in this work showed that new method causes the beam plastic rotation to increase by 30%. In addition, the applied force at the panel zone (according to the capacity of panel zone) is decreased. When compared to the frames without cuts, these reductions result in a 52% decrease in the plastic rotation of the panel zone, we also investigated the amount of dissipated energy by beams in the conditions before and after retrofitting. ANSYS software was used to study and analyze the non-linear behavior in the area of connections.}, Keywords = {Steel moment frame,RBS connection,ductility,Hysteretic loops,Panel zone}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بهسازی اتصالات صلب فولادی متداول از طریق کاهش مقطع بال}, abstract_fa ={چکیده- در زلزلههای اخیر اتصالات بسیاری از سازههای فولادی که دارای سیستم مقاوم قاب خمشی بودند دچار شکستگی ترد در جوش اتصالات تیر و ستون شدهاست. بر اثر تحقیقات مشخصساخت که بیشتر آسیبها بهعلت ترک خوردگی جوش بین بال پایینی تیر و ورق بال ستون ایجاد شده و بال بالایی بهعلت اثر اندرکنشی دال بتنی کف از خود مقاومت نشان دادهاست. برای جلوگیری از ترک خوردگی جوش و در نتیجه شکست ترد اتصال، از روشهای مختلف مقاوم سازی یا بهسازی میتوان بهرهبرد. با توجه به این نکته که بال بالایی تیر در داخل بتن کف قرار دارد و برداشتن دال کف از دیدگاه هزینه و مسائل اجرایی مشکلاست، اجرای طرح مقاومسازی در بال پایینی تیر میتواند بهترین گزینه جایگزین باشد. یکی از این اتصالات با مقطع ) RBS روشها برش بال پایینی تیر در مقطع خاص است. شکل برش مانند اتصالات کاهش یافته بال تیر) با برش شعاعی است و با این کار، اتصال، از حالت اتصال صلب معمولی به نوعی اتصال شکلپذیرتر تبدیل میشود که توانایی تحمل چرخش پلاستیک بیشتری را داشته وشکل پذیری سازه در مجموع افزایش مییابد. با توجه به تاثیر بسیار زیاد مقاومت چشمه اتصال در رفتار لرزهای و شکلپذیری اتصال، بررسی تاثیر این روش بر چشمه اتصال ضروری بهنظر میرسد. بررسیهای انجام شده مشخص در بال پایینی تیر، باعث افزایش 30 % در میزان چرخش پلاستیک تیر میشود. RBS ساخت که ایجاد اتصال همچنین نیروی واردشونده بر چشمه اتصال ( با توجه به مقاومت چشمه اتصال) کاهش مییابد که در نتیجه باعث کاهش 52 % در میزان چرخش پلاستیک در چشمه اتصال میشود. در این مقاله همچنین میزان تلف ANSYS انرژی تیر در دو حالت قبل و بعد از بهسازی مطالعه شدهاست. برای انجام تحلیلها از نرمافزار استفاده شده است.}, keywords_fa = {کلید واژگان : اتصال صلب فولادی,اتصالRBS شکل پذیری,منحنی هیسترسیس,چشمه اتصال}, url = {http://mcej.modares.ac.ir/article-16-8043-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-8043-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Zakeri, J. A. and Esmaieli, M. and Fathali, M.}, title = {Introducing New Humped Slab Track Superstructure for Obviating the Problems of}, abstract ={Abstract The movement of sand dunes in desert railways has various harmful effects, which reduces operational safety and speed and causes great maintenance and renewal costs. To encounter the movement of sand dunes, different traditional and modern methods are implemented, none of which covers completely the problems, especially the ballast solidification and line closuring as the major ones. In this paper, a new system called "humped slab track" is introduced, in which the ballast solidification problem is obviated with the application of ballast-less superstructure. The problem of track closuring with sand dunes is also mitigated by means of elevating the rails higher, using uncases reinforced concrete called "humps", and letting the sands traverse from the generated superstructure space between the humps and beneath the rails, just like fluid. To show the efficiency of the proposed system, the simulation of sand movements from the track section was performed using two-phase analysis in the FLUENT finite element software.}, Keywords = {eywords: Humped slab track,Sandy-dry,Ballast solidification,Track closure}, volume = {10}, Number = {2}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {معرفی روسازی نوین "دال خط کوهاندار" برای حل مشکل راه آهن مناطق کویری}, abstract_fa ={کیده- حرکت ماسههای روان در مناطق کویری از جنبههای مختلف بهویژه صلب شدن لایۀ بالاست روسازی و مسدود شدن خط ریلی، باعث کاهش ایمنی حرکت، کاهش سرعت و در نتیجه افزایش تأخیر قطارها و نیز افزایش هزینۀ نگهداری و بهسازی خط میشود. برای مقابله با حرکت ماسه های روان از درون خطوط ریلی روشهای مختلفی ارائه شده که هر یک به شکلی به حل مشکلات کمک میکند؛ اما هیچیک از روشهای موجود بهطور کامل به حل مشکل نپرداخته است. در این مقاله، به معرفی روسازی جدیدی با نام "دال خط کوهاندار"میپردازیم که ضمن حذف لایه بالاست در روسازی بهکمک خطوط بدون بالاست، مشکل صلبیت لایه بالاست بر اثر حرکت ماسههای روان از خط را نیز حل میکند در این سیستم همچنین با ارتفاعدهی مناسب به ریلها توسط زائده- های بتن آرمه موسوم به کوهان و ایجاد فضای عبور در هندسه روسازی، امکان عبور آزاد ماسه از خط فراهم شده است. برای نشان دادن کارایی سیستم دال خط پیشنهادی در عبور ماسه، شبیهسازی حرکت ماسههای روان از مقطع خط با بهرهگیری از تحلیل سیستمهای دو فازی و بهکارگیری نرم افزار اجزای محدود انجام شده است.}, keywords_fa = {واژگان کلیدی: ماسه روان,دال خط کوهاندار,صلبیت بالاست,مسدودشدن,تحلیل دوفازی}, url = {http://mcej.modares.ac.ir/article-16-109-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-109-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Komakpanah1, Ali and AghaMajidi2, Mohamm}, title = {Creep of Rock Fill Material in Large Scale Odometer with Considering Particle Breakage in Loss Angeles Test}, abstract ={Abstract Creep is a time-dependent deformation of soil under constant effective stresses. For investigation on the creep of rock fill materials, 3 samples from 3 dams of Iran that are already under construction were selected. Normal effective stresses were applied on the specimens with a large-scale odometer apparatus that is specially designed for the research. Comparison of creep rate, amount of particle breakage and results of Los Angeles test shows a relationship between these three parameters. Consequently Los Angeles test that is a simple and accessible test, can give a prediction and estimation of behavior and properties of rock fill materials. Based on the test results, an approximate relationship could be found between creep, particle breakage and Los Angeles test results.}, Keywords = {creep,Odometer Test,Rock Fill Material,Particle Breakage}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {یادداشت تحقیقاتی » خزش مصالح سنگریزه ای در دستگاه ادومتر با مقیاس بزرگ با رویکردی به پدیده شکست ذرات و آزمایش سایش لوس آنجلس}, abstract_fa ={چکیده- خزش، تغییر شکل مصالح تحت تنش ثابت با گذشت زمان است. برای مطالعه خزش مصالح سنگریزه ای، مصالح سه سد در حال ساخت در ایران انتخاب و این مصالح در دستگاه ادومتر بزرگ مقیاسی که برای این تحقیق طراحی و ساخته شد تحت آزمایش قرار گرفت. با مقایسه نرخ خزش این مصالح با میزان شکست ذرات و مقاومت سایشی نمونه ها در آزمایش لوس آنجلس رابط های بین این سه پارامتر مشاهده شد. بنابراین به آزمایش ساده لوس آنجلس می توان تخمی نهایی از رفتار مصالح سنگریزه ای به ویژه پارامترهای شکست ذرات و خزش به دست آورد. بر اساس نتایج به دست آمده از آزمایش های انجام شده در این تحقیق، رابطه ای تجربی بین پارامترهای خزش و شکست ذرات با نتایج آزمایش لو سآنجلس ارائه شده است.}, keywords_fa = {خزش,کلید واژگان: آزمایش ادومتر,مصالح سنگریز های,شکست ذرات}, url = {http://mcej.modares.ac.ir/article-16-9638-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-9638-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Nateghi., F. and Dehghani, A.}, title = {Analytical Behavior of Brick-Infilled Concrete Frames Strengthen by FRP}, abstract ={Abstract Due to various deficiencies, inadequate lateral stiffness, weak design and weak construction, many reinforced concrete buildings are highly damaged during the major earthquakes. One way to retrofit these buildings is to improve the behavior and to prevent the total collapse of the reinforce masonry infilled walls in order to make them behave such as structural walls with composite materials. In this study, the concept of equivalent strut is investigated by finite element modeling and behavior of the compression strut and tension tie is presented to model unretrofit and retrofit masonry infilled walls. Analytical pushover results show great accordance with experimental results.}, Keywords = {Seismic Strengthening,CFRP,Masonry infill,reinforced concrete frames,Pushover}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی تحلیلی مقاوم سازی قاب های بتنی با میانقاب مصالح بنایی (FRP) استفاده از پلیمرهای مسلح فیبری}, abstract_fa ={چکیده- بدیهی است ساختمان های بتنی که سختی جانبی کافی نداشته و به صورت ضعیف طراحی و اجرا شده اند، در هنگام وقوع زمی نلرزه های شدید آسی بهای قابل توجهی را تجربه می کنند. یکی از روش های مناسب مقاو مسازی این گونه ساختمان ها برای اصلاح رفتار سازه و جلوگیری از فروریزش، تقویت میانقا بهای به گونه ای است که این اعضا به صورت دیوارهای سازه ای (FRP) مصالح بنایی با کامپوزیت های پلیمر مسلح عمل کنند. در این مقاله ابتدا با استفاده از روش المان محدود، روش مدل سازی میانقاب با دستک معادل بررسی شده و سپس با معرفی رفتار دست کهای فشاری و کششی، میانقاب در دو حالت عادی و مقاوم شده مدل سازی شده است. نتایج تحلی لهای استاتیکی فزاینده غیرخطی نشان م یدهد که مدل ارائه شده توانسته است رفتاری نزدیک به رفتار نمون ههای آزمایشگاهی ارائه کند.}, keywords_fa = {المان محدود,کلید واژگان: ساختمانهای بتنی,کامپوزیت های پلیمر مسلح,میانقاب,تحلیل استاتیکی فزاینده غیرخطی}, url = {http://mcej.modares.ac.ir/article-16-4301-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4301-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Mansoori, A. R. and SalehiNeyshabouri, S. A. A. and Honarbakhsh, A.}, title = {3D Numerical Analysis of Bed Topography in 180 Degree Channel Bend}, abstract ={Abstract The complex three-dimensional flow characteristics in river bends necessitates the use of a three-dimensional numerical model. The numerical model used in this paper is called SSIIM (Sediment Simulation In Intakes with Multiblock option).The 3D model already has showed satisfactory results in related applications. In this study, SSIIM is applied to study the variation of channel bed under steady flows in a 180 mild curved open-channel with sandy bed. Bed roughness was calibrated to ks 4.5 d90 6.25d50 . Comparison of results showed good agreement between the computed and measured bed topography. The model simulated both the point bars near the inner bank and the scour holes near the outer bank. In addition, the positions of these phenomena are in fair agreement with the measured data. Numerical results show some dependencies on the grid size. In addition, deviations of model from the experimental data as well as uncertainties in numerical modeling are discussed.}, Keywords = {Bed Topography,secondary flow,River,Bend,numerical simulation,CFD,SSIIM}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {مطالعه عددی سه بعدی تغییرات تراز بستر در قوس 180 درجه}, abstract_fa ={چکیده- خاصیت س هبعدی جریان در خم های رودخان های، لزوم بررسی الگوی جریان و انتقال رسوب در این مجاری را با استفاده از مدل های عددی س هبعدی مطرح م یسازد. در تحقیق حاضر، با استفاده از مدل عددی تغییرات تراز بستر (پوشیده از ماسه یکنواخت) در قوس 180 درجه با انحنای نسبی (SSIIM) « سیم » سه بعدی ملایم بررسی شده است. واسنجی ارتفاع زبری بستر نشان می دهد که بهترین همخوانی با داد ههای گزارش شده حاصل می شود. در این حالت مدل می تواند پشته رسوبی و ks  4/5 d90  6/25d50  8mm آزمایشگاهی در ناحیه فرسایشی مورد انتظار در نیمه اول قوس و همچنین نواحی فرسایشی و رسوب گذاری نیمه دوم قوس را به خوبی مدل سازی کند؛ هرچند مقادیر حداکثر آبشستگی بستر و حداکثر ارتفاع تاج ناحیه رسوب گذاری در کانال، بیشتر از مقادیر آزمایشگاهی پی شبینی شده است. همچنین در ادامه، با هدف بررسی تأثیر پارامترهای مؤثر بر فیزیک مسأله، اثر تغییر در ضریب زبری، اندازه شبکه میدان و همچنین اثر تغییر در عدد فرود جریان بر پیش بینی نتایج حاصل از شبیه سازی عددی بررسی شده است. نتایج این بررس یها نشان داد که با تغییر در میزان زبری بستر، مقدار فرسایش در قیاس با مقدار رسوب گذاری در بستر، تغییر بیشتری از خود نشان می دهد. بررسی اثر اندازه شبکه میدان نیز نشان داد که مدل تا حدی به اندازه شبکه حساس است. تغییر در عدد فرود جریان نیز به طور قابل توجهی بر میزان تغییرات شیب عرضی بستر اثر می گذارد.}, keywords_fa = {کلید واژگان: تغییرات تراز بستر,توپوگرافی,جریان ثانویه,تنش برشی,قوس 180 درجه,شبیه سازی عددی}, url = {http://mcej.modares.ac.ir/article-16-4297-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4297-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Naderi, M. and Maadani, S.}, title = {‹‹Research Note›› Determination of Strengths of Construction Materials Applying the in Situ Twist off Method}, abstract ={Abstract Since for some reasons such as studying the behaviour of old construction materials and proper replacement of the deteriorated sections, adequate knowledge about the true in situ strength of the construction materials has become a necessity, many attempts have been made to invent and develop new in situ methods in recent years. Most of these methods measure the in situ strengths of materials indirectly by measuring properties other than the strength and relating them to strength by some defined relationships. This paper introduces an innovative partially destructive method, called “Twist-off”, for the assessment of in situ concrete, mortar, and masonry strengths of materials used in buildings and structures. In addition to the laboratory results, the results of the successful application of this method on site are also presented in this paper. Based on the results obtained, the use of this new in situ method with its advantages of simplicity (no need for experts), low expense, cheap and simple apparatus, little damage to the surface area, and high accuracy is strongly recommended for the determination of in situ strengths of construction materials (concrete, mortar, and masonry) used in different buildings and structures.}, Keywords = {In Situ Strength,Material Strength,Twist off Method,Determination of Strength}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {تعیین مقاومت مصالح در ساختمان ها « پیچش » با استفاده از روش درجای}, abstract_fa ={چکیده - از آنجا که برای مطالعه رفتار و دوام و همچنین برای جایگزینی مناسب مواد و مصالح در تعمیر و مرمت، آگاهی از مقاومت واقعی مصالح بکار گرفته شده در بناها از اهمیت ویژه ای برخوردار است و با توجه به اینکه شرایط رایج در استفاده از رو شهای آزمایشگاهی با شرایط محیطی و بهر هبرداری این بناها کاملاً متفاوت می باشند، در سال های اخیر کوشش های زیادی برای ابداع روش های درجا بعمل آمده است ولی در اغلب این روش ها، پارامترهایی به صورت غیرمستقیم اندازه گیری و سپس با استفاده از روابطی، مقاومت مصالح موردنظر که در این مقاله به آن پرداخته شده است، روشی است که می توان با « پیچش » تخمین زده می شود. روش به کارگیری آن مقاومت واقعی و درجای مصالح بکارگرفته شده در ساختمانها، از جمله بتن, ملات، آجر و سنگهای بکار می رود چون قسمت بسیار کوچکی « بطور مستقیم » مصرفی را بطور مستقیم بدست آورد. به این دلیل عبارت از مصالح مورد نظر شکسته شده و مقاومت آن به دست می آید. از بررسی های آزمایشگاهی و مطالعات درجای بعنوان روشی کم هزینه و مطمئن (دقت بالا) برای اندازه گیری مقاومت درجای مصالح « پیچش » بعمل آمده، روش در ساختمان ها پیشنهاد می گردد. همچنین، این روش می تواند با دقت قابل قبولی برای بررسی رفتار و دوام مصالح بکار رفته در بناها ونیز برای انتخاب بهینه مواد و مصالح جایگزین برای تعمیر و مرمت این گونه سازه ها بکار گرفته شود. از جمله امتیازات این روش می توان به سادگی روش، ارزانی و سادگی ابزار بکار گرفته شده، کم هزینه بودن آن، آسیب بسیار ناچیز بجا مانده و عدم نیاز به متخصص و یا نیروی ماهر اشاره نمود.}, keywords_fa = {کلید واژگان: مقاومت در جا,مقاومت مصالح,روش پیچش,تعیین مقاومت}, url = {http://mcej.modares.ac.ir/article-16-7587-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-7587-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Ghanbari, A. and Shekarian, S. 2}, title = {Research Note›› Determination of Active Earth Pressure for Reinforced Retaining Walls in c-) Soils}, abstract ={Abstract The prediction of active earth pressures is essential to the design of retaining walls in case of reinforced and unreinforced soils. In this study, a new analytical method is presented to determine the coefficient of earth pressure. The horizontal slice method is used to compute the active earth pressure behind a rigid retaining wall in consideration of the granular soils. To verify the correctness of the suggested method, its results were compared with those of existing studies. Results show that the developed formulation for non-cohesive soils has a good agreement with the results of software simulations. Also, a new formulation for cohesive soils was presented and its results were compared with the Rankine method. The effect of parameters such as the cohesion of soil mass, the angle of internal friction and the angle of wall friction were assessed. In all cases, it is shown that the horizontal slice method has good capability to predict the active earth pressure.}, Keywords = {Earth Pressure,Retaining Wall,Horizontal Slice,Reinforced soil}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {یادداشت تحقیقاتی » تعیین فشار فعال استاتیکی وارد شونده بر دیوارهای مسلح شده در خاک های اصطکاکی و چسبنده}, abstract_fa ={چکیده - محاسبه فشار خاک وارد شونده بر دیوارهای حایل یکی از مسائل اساسی در مهندسی ژئوتکنیک است. در این نوشتار بر مبنای رو شهای تحلیلی، تعیین فشار وارد شونده بر دیوارهایی که تود ههای خاک مسلح در پشت آنها قرار می گیرد، مطالعه شده است. به این منظور روش قطعات افقی مورد بازنگری و تدقیق قرار گرفته و فرمول بندی کامل آن برای خاک های اصطکاکی ارائه شده است. بر مبنای این فرمول بندی فشار خالص وارد شونده بر دیوار محاسبه شده و با نتایج به دست آمده از روش های دیگر مقایسه شده است. همچنین فرمول بندی جدیدی برای ارزیابی فشار واردشونده بر دیوار در خاک های چسبنده ارائه و نتایج آن با روش رانکین مقایسه شده است. بررسی های نشان می دهد که روش قطعات افقی از قابلیت مناسبی برای تحلیل دیوارهای حائل در شرایط مختلف برخوردار است.}, keywords_fa = {کلید واژگان: فشار برایند خالص,روش قطعات,دیوار حایل,خاک مسلح}, url = {http://mcej.modares.ac.ir/article-16-5193-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-5193-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Lotfollahi-Yaghin, M. A. and Negin, M.}, title = {Effect of Random Initial Crookedness of Members on Reliability of Steel Frames}, abstract ={Abstract In this paper the effect of two types of common initial geometric imperfections on the reliability of steel frames is investigated. These imperfections are the coordinates of connection nodes and crookedness of members. Most finite element reliability analyses in past literature neglect this source of uncertainty. For this purpose static nonlinear pushover structural analysis is used from which reliabilities are estimated based on FORM and Monte Carlo sampling methods. Furthermore to investigate the importance of uncertain parameters, reliability sensitivity analysis is performed by use of the direct differentiation method which has been implemented in the object oriented software framework Open Sees. It is demonstrated that some of these geometric imperfections have significant influence on reliability assessment of steel frames.}, Keywords = {Steel Frames,Geometric imperfections,Reliability,Sensitivity,Open Sees}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {بررسی اثر انحنای اولیه تصادفی اعضا در قابلیت اعتماد قاب های فولادی}, abstract_fa ={چکیده- در این مقاله اثر ناکاملی های هندسی اولیه در قاب های فولادی به دو شکل یعن ی ناکامل ی هندس ی موجود در مختصات گر ههای اتصالی اعضای سازه به یکدیگر و ناکاملی هندسی ناشی از وجود انحنا در راستای اولیه و تئوری اعضای مختلف سازه که کمتر در مطالعات گذشته به صورت متغیرهایی تصادفی در تحلیل های وارد شده ظرفیت باربری و قابلیت اعتماد این سیستم ها مطالعه شده است . ب ه ای ن منظور با انجام تحلیل استاتیکی و غیرخطی پوش اُور و با استفاده از روش های مرتب ه اول قابلی ت اعتما د و ش بیه ساز ی مونت کارلو قابلیت اعتماد سیستم های مورد نظر محاسبه می شوند. علاوه بر این با ب ه کارگ یری تحلیل حساس یت به روش پیاده سازی شده، اهمیت هر ی ک از متغیرها ی OpenSees مشتق گیری مستقیم که در ساختار شیءگرای نرم افزار تصادفی مذکور از نظر میزان تأثیری که در رفتار سیستم دارند ارزیابی می شود. نتایج ب هدست آمده نشان می دهند که برخی از ناکاملی های هندسی مذکور از اهمیت ویژه ای در قابلیت اعتماد این سیستم ها برخوردارند که این نشان دهنده اهمیت تغییرات هرچند کوچک این پارامترها در احتمال خرابی قاب های فولادی است.}, keywords_fa = {ناکاملی های هندسی,قابلیت اعتماد,حساسیت,.OpenSees کلید واژگان: قاب های فولادی,نرم افزار}, url = {http://mcej.modares.ac.ir/article-16-6822-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6822-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Barghi1*, M. and Lagzian, A}, title = {Shear Strength Degradation of Circle Reinforced Concrete Columns}, abstract ={Abstract Earthquake reconnaissance has identified shear failure of reinforced concrete columns as a primary cause of failure of older existing reinforced concrete columns. Satisfactory seismic response of reinforced concrete columns requires that brittle failure modes be inhibited. In this research, different factors which affect the shear failure of columns have been studied, and then by using the results of 103 cyclic loading tests on columns, a new model for estimation of shear strength degradation under cyclic loading has been developed. The proposed model can be used to estimate shear strength degradation of reinforced concrete columns with shear, shear flexural and flexural failure separately. Uncertainty of the results of this model is little because the study has been concentrated on the three independent groups of the columns with one specified failure mode. The results of cyclic loading tests used in this study have been taken from the PEER ( Pacific Earthquake Engineering Research Center) database.}, Keywords = {Shear Failure,Shear Strength,Cyclic loading,Columns,reinforced concrete}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {کاهش مقاومت برشی بر اثر تغییر مکان جانبی ستون استوانه ای بتن مسلح}, abstract_fa ={چکیده - انهدام برشی، یکی از علل خرابی ستون های بتن آرمه بر اثر بار زلزله و بارهای تناوبی است. در این تحقیق عوامل مختلف مؤثر در این نوع انهدام بررسی می شود. مدل های گوناگونی که توسط محققان و مؤسسات تحقیقاتی برای محاسبه کاهش مقاومت برشی مقاطع ستون ها ارائه شده، مطالعه شده و سپس مدل جدیدی ارائه می شود. این تحقیق بر اساس نتایج 102 آزمایش بارگذاری تناوبی بر روی ستون هایی با مقطع دایره ای انجام شده است. این نتایج از بانک اطلاعاتی مؤسسه تحقیقاتی زلزل هشناسی پاسیفیک برداشت شده است. در مدل پیشنهادی ابتدا نوع انهدام ستون تعیین و سپس درصد کاهش مقاومت برشی آن با توجه به شکل پذیری ستون تخمین زده می شود.}, keywords_fa = {کلید واژگان: انهدام برشی,کاهش مقاومت برشی,بارگذاری تناوبی,ستون های بتن آرمه,خرابی ستون ها}, url = {http://mcej.modares.ac.ir/article-16-5115-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-5115-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {.Afshar, M.H and Daraeikhah, M.}, title = {Evaluation of Genetic Algorithms for Optimal Design of Cascade Stilling Basins}, abstract ={Abstracts This paper presents how the genetic algorithm (GA) can be applied to design of cascade stilling basins. Genetic Algorithm is adaptive method, which can be used to solve search and optimization problems over a period of generations, based upon the principles of natural selection and survival of the fittest ones. The objective of this research is to minimize total cost of construction effectively which is a function of height of falls and length of stilling basins, while fulfilling the hydraulic and topographical criteria. The efficiency of GA discussed here has been tested for a benchmark example and the result for this algorithm is compared with the other method introduced by Vittal and Porey. The results clearly reveal superiority of the GA algorithm}, Keywords = {Genetic algorithm,Fitness,Selection,Cross Over,Mutation,Parent,Stilling basin}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {کمینه سازی هزینه سرریزهای متوالی در سدهای بلند با استفاده از الگوریتم ژنتیک}, abstract_fa ={چکیده- در این مقاله عملکرد الگوریتم ژنتیک در طراحی بهینه سرریزهای متوالی مطالعه شده است. الگوریتم ژنتیک جزء روش های جستجوی فراکاوشی محسوب می شود که تکامل طبیعی موجودات را الگو قرار می دهد . هدف از این تحقیق ، یافتن مقادیری برای ارتفاع و طول سرریزهای متوالی است که ضمن ارضای تمامی قیدهای هیدرولیکی و توپوگرافی مسأله ، کمترین هزینه ساخت را داشته باشد. کارایی مدل بهین ه سازی ار ائ ه شده ، با مقایسه نتایج حاصل از روش سنتی معرفی شده توسط ویتال و پوری، آزمایش شده است.}, keywords_fa = {کلید واژگان: الگوریتم ژنتیک,برازندگی,انتخاب,آمیزش,جهش,سیستم سرریزهای متوالی}, url = {http://mcej.modares.ac.ir/article-16-384-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-384-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {SHAKIB, H. and Hashemi2*, S.SH}, title = {Evaluation and Comparison of Real, Artificial and Pulse-Like Models Near-Fault Earthquakes}, abstract ={Abstract Ground motions close to a ruptured fault can be significantly different from those further away from the seismic source. In the other hand there are a few real records which include the characteristic of near-fault records. Hence, simulation of these records is useful in order to study their effects on the behavior of structures which has been built near the faults. Tehran is a city in the neighboring of several active faults but there aren’t any nearfault real records in this place. In this paper, according to mechanism and situation of North Tehran Fault (NTF), seven near-fault real records with forward directivity have been selected and by using selected records a pulselike decaying sinusoidal model has been proposed as NTF simulated near-fault records. Finite fault method with specific considerations has been used as a suitable and reliable method for creating near-fault artificial record and the artificial records for NTF has been generated at 2, 5 and 10 km distances. Finally the results for real and artificial records and also the pulse-like model have been compared together.}, Keywords = {Near-Fault Earthquakes,Artificial Record,North Tehran Fault,Pulse-Like Model}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {ارزیابی و مقایسه زلزله های واقعی، مصنوعی و مدل های ضربه گونه جایگزین نزدیک گسل}, abstract_fa ={چکیده- با توجه به اینکه در فواصل نزدیک به گسل تعداد رکوردهای واقعی زلزله اندک است و از طرف دیگر وجود ویژگی های خاص در رکوردهای نزدیک گسل که ما را به استفاده از رکوردها ی دور از گسل محدود می سازد، استفاده از رو شهای شبیه سازی رکورد مفید است. به عنوان مثال در ناح ی ه تهران عل ی رغم قرارگیری در نزدیکی چند گسل اصلی و لرزه زا، هیچ رکورد واقعی ای برای آن وجود ندارد. اگر با استفاده از روش های شبیه سازی و با حفظ ویژگی های رکورد نزدیک گسل، برای این منطقه رکورد مصنوعی نزدیک گسل تهیه شود، می تواند در طراحی بهتر ساز ههای قرار گرفته در نزدیکی گسل به ما کمک کند. در این تحقیق پس از بررسی رکوردهای واقعی نزدیک گسل ، ضمن بررس ی مدل ها ی مختلف ضربه گون ه ارائه شده برای جایگزینی رکوردهای نزدیک گسل، مدل سینوسی می را انتخاب شده و با استفاده از آن مدل ضربه گونه متناسب با رکوردهای واقعی تهیه شده است . همچنی ن ضمن بررس ی روش ها ی مختلف ایجاد رکوردهای مصنوعی زلزله، روش گسل محدود با اعمال شرایطی خاص به عنوان روش ی مناسب برای ایجاد رکورد مصنوعی نزدیک گسل استفاده شده و رکوردهای مصنوعی متناسب با رکوردهای واقعی تهیه شده است . سپس در ادامه این سه نوع رکورد مقایسه شده است. با توجه به اینکه در نزدیک ی گسل شمال تهران رکورد واقعی نزدیک گسل وجود ندارد، متناسب با این منطقه مدل ضربه گونه ای به عنوان رکورد نزد ی ک گسل و همچنین رکورد مصنوعی نزدیک این گسل ایجاد شده و مورد مقایسه قرار گرفت ه است.}, keywords_fa = {کلید واژگان: رکورد نزدیک گسل,رکورد مصنوعی,گسل شمال تهران,مدل ضربه گونه}, url = {http://mcej.modares.ac.ir/article-16-8072-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-8072-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {KHEIRODIN, A. and FAMILY, S.}, title = {Seismic Evaluation of Concrete Moment Frames with Low Height Beams}, abstract ={Abstract Low height beams in concrete moment frames, decrease the ability of beams in controlling lateral displacement of buildings. Because of that, in the sixth subject from Iranian Regulations of Buildings and its following, in the 3rd edition of Standard 2800, the height of buildings with low height beams has been limited to 3 floors or 10 meters. According to that, in this study, concrete buildings with different amount of stories and moment frames, with medium ductility and the height of beams in 30 centimeters, have been analyzed (with linear equivalent static and spectral dynamic analysis Methods)and designed on the basis of seismic principles in the 2nd and 3rd edition of Standard 2800. Finally, studies continued with nonlinear static analysis and the performance point of structures determined (with capacity spectrum and displacement coefficient methods) in 4 levels of different seismic risks. Studies show that only one or two story buildings that designed with 2nd edition of Standard 2800 have enough safety in design base earthquake level (DBE) and also higher buildings, should go under rehabilitation.}, Keywords = {Reinforced Concrete Structures,nonlinear static analysis,Performance level,Moment frame,Lateral Displacements}, volume = {10}, Number = {1}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {ارزیابی لرزه ای سیستم قاب خمشی بتنی با تیرهای کم ارتفاع}, abstract_fa ={چکیده - ارتفاع کوتاه تیرها در سیستم مقاوم جانبی قاب خمشی بتن آرمه، می تواند موجب ناکارامد ی تیرها در کنترل تغییرمکان های جانبی سازه شود. از این رو در مبحث ششم مقررات مل ی ساختمان و به تبع آن در ویرایش سوم استاندارد 2800 ، ضابطه ای به منظور محدود ساختن ارتفاع ساختمان های با سقف تیرچه بلوک و سیستم مقاوم جانبی قاب خمشی و تیرهای با ارتفاع 30 سانتی متر در نظ رگرفته شده تا ارتفاع این گونه سازه ها به سه طبقه یا 10 متر محدود شود. بر همین اساس در این مطالعه ساختمان های بتنی با ضخامت سقف و ارتفاع تیر 30 سانتی متر و سیستم مقاوم جانبی قاب خمشی با شکل پذیری متوسط، بادر نظرگرفتن تعداد مختلف طبقات بر اساس ویرایش های دوم و سوم استاندارد 2800 مورد تحلیل های استاتیکی و دینامیکی خطی و سپس طراحی قرارگرفته و سرانجام با تحلیل استاتیکی غیرخطی و با استفاده از هر دو روش محاسبه نقطه عملکرد (روش ضرایب تغییر مکان و روش طیف ظرفیت)- در دستورالعمل بهسازی و تفسیر آن تشریح شده - برای چند سطح خطر لرز های مختلف، مورد ارزیابی و آسیب پذیری لرزه ای قرارگرفته است. نتایج نشان می دهند که فقط ساختمان های یک و دو طبقه طراحی شده بر اساس ویرایش دوم استاندارد 2800 ، ایمنی لازم را در برابر زلزله طرح استاندارد 2800 داشته و برای ساختمان های بلندتر، عملیات مقاوم سازی باید انجام شود.}, keywords_fa = {ساختمان های بتن آرمه,تحلیل غیرخطی استاتیکی,سطح عملکرد,قاب خمشی,تغییرمکان های جانبی}, url = {http://mcej.modares.ac.ir/article-16-3473-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-3473-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {RezaieePajand1, M. and Firoozi2, S.T.}, title = {119 Abstract «Research Note» Measuring the Abilities of Four Approximation Approaches for Trusses Optimization}, abstract ={There are a lot of approximation techniques for structural optimization. Among them, four outstanding approximation methods have been selected for trusses optimization. These approaches have been developed or modified by previous ones. Based on these schemes, a lot of trusses have been optimized by author's program. This study shows that the abilities of the mentioned methods are not the same and some of them have deficiencies. Reaching a better solution, lesser analysis time, oscillation of response, numerical stability and also using a variety of the design variables are among the findings of this work. A brief of these obtained results has been given in the conclusion part.}, Keywords = {Nonlinear programming,Global optimum,Approximation methods,Convex approximation,Structural Analysis,Two and three dimensional trusses}, volume = {10}, Number = {4}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {سنجش توانایی های چهار راهکار تقریبی بهینه سازی خرپاها}, abstract_fa ={چکیده- فن های تقریبی بهینه سازی سازه ها فراوانند. از میان آن ها، چهار روش تقریبی توانا بر ای بهینه کردن خرپاها، اختیار و معرفی می شوند. این راهکارها، از تغییر و یا بهبود روش های تقریبی پیشین به دست آمده اند. بر پایه این شیوه های تقریبی، سازه ها ی خرپایی بسیاری، با برنامه رایانه ای نویسندگان تحلیل شده اند. به سبب حجم محدود مقاله، در این جا تنها درباره ی شمار ی از سازه های تحلیل شده، بحث می شود. این پژوهش مشخص کرد که این چهار فن تقریبی، توانایی ها ی یکسانی ندارند و پاره ای از آن ها کاستی هایی دارند. رسیدن به پاسخ بهتر، زمان کم تر تحلیل، نوسان پاسخ ها، پایداری عددی و هم چنین تنوع به کار بردن متغیرها، از میان ویژگی های آشکار شده است. خلاصه ای از یافته های این چهار روش در بخش نتیجه گیری می آید.}, keywords_fa = {برنامه ریزی غیرخطی,بهینه کلی,راهکارهای تقریبی,تقریب کوژ,تحلیل سازه ها,خرپای مستوی و فضایی}, url = {http://mcej.modares.ac.ir/article-16-11444-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-11444-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {SoltaniMohammadi1, M and Ghiassi2, bahm}, title = {«Research Note» A Review of Foundations Evaluation Using Seismic Codes}, abstract ={Abstract: The experience of last earthquakes has shown the vulnerability of most of structures. This has been caused the speeding up of the seismic evaluation and retrofitting of projects in Iran. In this regard, the instructions for seismic rehabilitation of the existing buildings have been published and are currently beiong used in the evaluation and retrofitting projects. The experience of retrofitting the structures in the past has shown that one of the most important problems in Iran is seismic evaluation and retrofitting of the foundations. The evaluation procedures are usually done such that they results in huge retrofitting plans for foundations and this opinion has been raised that seismic evaluation and retrofitting of the structures is not economical. This paper presents some suggestions for accurate seismic evaluation of structural and geotechnical components of foundations. The results showed that by using the correct relations and understanding the behavior of structure exactly, the retrofitting procedure do not result in massive strengthening.}, Keywords = {Seismic evaluation,Rehabilitation,Foundation}, volume = {10}, Number = {4}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {کاوشی در ارزیابی آسیب پذیری و بهسازی لرزه ای ساختمان ها در تراز پی برمبنای ضوابط دستورالعمل بهسازی لرزه ای}, abstract_fa ={چکیده- تجربه زلزله های گذشته، آسیب پذیری بسیاری از ساختمان های موجود در کشورمان را نشان داده است. این تجربه باعث افزایش سرعت انجام طرح های بهسازی و ارزیابی آسیب پذیری لرزه ای ساختمان های موجود شده است . بدین منظور دستورالعمل بهسازی لرزه ای ساختمان های موجود تهیه شده که در امر ارزیابی آسیب پذی ری لرزه ای و بهسازی ساختمان ها مورد استفاده متخصصین و مهندسین است. تجربه چند ساله مقاوم سازی در کشورمان نشان داده است از جمله مشکلاتی که در ارزیابی لرزه ای ساختمان ها با آن برخورد می شود، ارزیابی و بهسازی در تراز پی است. ارزیابی لرزه ای پی های ساختمان ها عموماً، به گونه ای بوده که منجر به تهیه طرح های مقاوم سازی بسیار حجیم در این تراز شده و این گمان پیش آمده است که ارزیابی و بهسازی پی ها با استفاده از دستورالعمل، غیراقتصادی است. در این مقاله سعی بر آن است که به علل و عوامل وقوع این مسئله پرداخته شود و هم چنین با کندوکاوی در ضوابط دستورالعمل بهسازی لرزه ای، نشان داده شود که ارزیابی لرزه ای و بهسازی در تراز پی، در صورت استفاده صحیح از روابط و ضوابط دستورالعمل و فهم دقیق رفتار سازه، نمی تواند منجر به پاسخ های غیر واقعی و یا غیراقتصادی شود.}, keywords_fa = {ارزیابی لرزه ای,دستورالعمل بهسازی,پی,شالوده}, url = {http://mcej.modares.ac.ir/article-16-9558-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-9558-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Bemanian, m.r and Okhovat, m.r and Okhovat3, H}, title = {«Research Note» Vibration Control of High-rise Buildings with Tuned Mass Dampers (Case Study: Tehran International Tower)}, abstract ={Abstract: Appealing to the principle of vertical residence and stemming the horizontal expansion of the city, the Tehran Milad Tower is being built on 35000 sm3 site with the total area of 220000 sm3. With a height of over 170m, this 56-story concrete building is in the final stages of construction and would be the highest residential building of Iran. Since Tehran is located in a high-risk earthquake zone, all of its structures must be designed for seismic loads. In this building, the lateral loads are carried with three main shear walls, which are located in an angle of 120 degrees and the gravity loads are transferred from the concrete slabs to the secondary shear walls. Since the introduction of Tuned Mass Dampers (TMD) by Frahm in 1909, as a passive control system, numerous investigations have been carried out to examine the effect of these devices in reducing seismic response of the structures. The objective of incorporating a TMD into a structures is to reduce the energy dissipation demand on the primary structural members subjected to external forces. This reduction is accomplished by transferring some of the structural vibration energy to the TMD and dissipating the energy at the damper of TMD. The purpose of this paper is to design and evaluate the effectiveness of TMD for response reduction of the Tehran tower under seismic excitations. A lumped mass model of the building was provided with 112 translational and 56 rotational degrees of freedom using solid and shell elements. Time history analyses were performed to calculate the response of the structure subjected to some earthquake records. The same procedure was followed for the models with attached TMD. The control effectiveness of TMD was evaluated by comparing the tower's responses with those of the towers without control device. Furthermore, multiple tuned mass dampers are suggested as a solution for insufficiency of TMD.}, Keywords = {Vibration Control,Tuned Mass Dampers (TMD),Tehran tower,Lateral Loads}, volume = {10}, Number = {4}, pages = {0-0}, publisher = {Tarbiat Modares University}, title_fa = {تحلیل عددی کنترل ارتعاشات ساختمان های بلند با استفاده از سیستم جرم میراگر متوازن مطالعه موردی: ساختمان برج بین المللی تهران}, abstract_fa ={کیده- سیستم های جذب انرژی غیرفعال سازه ها، در سال های اخیر به طور وسیعی در صنعت ساختمان استفاده شده اند. به طور کلی، این سیستم ها شامل وسایل و مصالحی می شوند که میرایی، سختی و مقاومت سازه را افزایش داده و می توانند بر ای کاهش خطرات طبیعی محتمل و نیز مقاوم سازی سازه های جدید یا ساخته شده به کار روند. با وجود ای ن، متأسفانه در صنعت ساختمان کشورمان، چندان مورد توجه قرار نگرفته اند. سیستم کنترلی جرم میراگر متوازن 1، یک میراگر غیرفعال نسبتاً جدید است که مطالعه راجع به آن و استفاده از آن در سال ها ی اخیر انجام شده است. عملکرد این سیستم بر اساس استهلاک انرژی ارتعاشی سازه به شکل حرکت نوسانی جرم میراگر است . در این پژوهش، عملکرد سیستم جرم میراگر متوازن تحت تحریک زمین لرزه، برای یک سازه بلند خاص که به خاطر سیستم سازه ای به کار رفته در آن، شکل پذیری چندانی ندارد، مطالعه شده است. نتیجه آن که اگرچه یافته های حاصل تا حد زیادی به ویژگی های شتاب نگاشت مورد استفاده در تحلیل وابسته است، حتی با استفاده از جرمی کوچک در مقایسه با جرم خود سازه، می توان پاسخ تغییر مکان و شتاب سازه را به میزان نسبتاً مناسبی کاهش داد. از سوی دیگر، نتایج نشان می دهد که سیستم جرم میراگر متوازن نسبت به فرکانس تنظیمی خود بسیار حساس است؛ از این رو استفاده از سیستم جرم میراگر چندگانه 2 برای رفع این اشکال پیشنهاد می شود.}, keywords_fa = {کنترل ارتعاشات,جرم میراگر متوازن,سازه های بلند,برج بین المللی تهران}, url = {http://mcej.modares.ac.ir/article-16-7348-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-7348-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {mirzaee, maged and rozagar, gafar}, title = {Measuring the Abilities of Four Approximation Approaches for Trusses Optimization}, abstract ={There are a lot of approximation techniques for structural optimization. Among them, four outstanding approximation methods have been selected for trusses optimization. These approaches have been developed or modified by previous ones. Based on these schemes, a lot of trusses have been optimized by author's program. This study shows that the abilities of the mentioned methods are not the same and some of them have deficiencies. Reaching a better solution, lesser analysis time, oscillation of response, numerical stability and also using a variety of the design variables are among the findings of this work. A brief of these obtained results has been given in the conclusion part. Keywords: Nonlinear programming, Global optimum, Approximation methods, Convex approximation, Structural analysis, Two and three dimensional trusses}, Keywords = {Nonlinear programming,Global optimum,Approximation methods,Convex approximation,Structural Analysis,Two and three dimensional trusses}, volume = {10}, Number = {4}, pages = {1-12}, publisher = {Tarbiat Modares University}, title_fa = {شبیه سازی ترک در ورق ها و پوسته ها با استفاده از روش اجزای محدود توسعه یافته}, abstract_fa ={چکیده- در این تحقیق، مدل سازی ویژه ای برای ورق ها و پوسته های دارای ترک با استفاده از روش اجزای محدود توسعه یافته انجام شده است. در ابتدا با استفاده از فرضیات ساده شونده کیرشهف فرمول بندی اجزای محدود استاندارد پوسته ارائه شده و پس از تدوین کد مربوط، با حل چند مثال از کارایی آن اطمینان حاصل شده است. برای ایجاد تأثیر حضور ترک، از توابع غنی ساز جدید و متناسب با میدان تغییرمکان استفاده شد. با افزودن بردرجات آزادی گره های اطراف ترک طی فرایند غنی سازی، شبیه سازی ترک در ورق ها و پوسته ها انجام شده است. این توابع از جواب های تحلیلی مسئله شکست ورق کیرشهف تحت بارگذاری های صفحه ای و خمشی استخراج شده اند. با حل چند مثال و مقایسه نتایج به دست آمده با جواب های تحلیلی موجود و نتایج حاصل از نرم افزارهای دیگر، اثبات می شود که نتایج کد دارای دقت قابل قبولی بوده و کارایی آن در تحلیل ورق ها و پوسته های ترک دار مناسب است.}, keywords_fa = {ورق کیرشهف,پوسته دارای ترک,اجزای محدود توسعه یافته,غنی سازی}, url = {http://mcej.modares.ac.ir/article-16-6475-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6475-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Omidvar, babak and Rahimian, mohamad and mohamadnagad, taktom and sanaeeha, ali}, title = {Direct Calculation of Free Term Coefficients in Displacement Boundary Integral Equations for 3-D Isotropic Problems}, abstract ={Abstract: Direct calculation of free term coefficients for linear isotropic problems in three dimensional displacement boundary integral equations is presented in details. In addition, the shape functions of 9 node non-continuous and semi-continuous elements for modeling the crack surfaces, layers interface, infinite boundary and other similar problems have been demonstrated. This proposed method for calculating cij coefficients has been verified comparing with some solved problems.}, Keywords = {Boundary element method,Free term coefficient,Boundary integral equation,Singular integral}, volume = {10}, Number = {4}, pages = {13-24}, publisher = {Tarbiat Modares University}, title_fa = {محاسبه مستقیم ضرایب ترم آزاد در معادلات انتگرال مرزی تغییرمکانی برای مسائل ایزوتروپ سه بعدی}, abstract_fa ={ده- در این مقاله ضمن مرور چگونگی حصول معادله انتگرال مرزی جابه جا یی با استفاده از قضیه برای مسائل ایزوتروپ خطی در محیط سه بعدی، به تفصیل ارائه می شود . با استفاده از نتایج cij محاسبه مستقیم ضرایب ترم آزاد تحقیق حاضر امکان محاسبه مستقیم ضرایب ترم آزاد در مدل سازی مسائل بی نهایت و نیمه بی نهایت که نمی توان از مفهوم حرکت جسم صلب برای محاسبه این ضرایب استفاده کرد، فراهم می شود. فرمول بندی ارائه شده در مسائلی که شرط همواری در محل تلاقی المان های پیوسته، صادق نیست نیز کاربرد دارد. هم چنین توابع شکلی مربوط به المان های غیرپیوسته، و نیمه پیوسته درجه دوم نه گره ای که در مدل سازی سطوح ترک، فصل مشترک لایه ها، مرزهای انتهایی محیط های نامحدود و بسیاری مسائل دیگر کاربرد با حل و بررسی مثال های مکعب تحت تنش ،cij دارد، ارائه می شود. صحت و کارایی روش پیشنهاد شده برای محاسبه ضرایب یکنواخت، تیر طرّه تحت حرکت جانبی در تکیه گاه، کره الاستیک تحت تنش یکنواخت و تحت جابه جا یی یکنواخت و در نهایت حفره کروی تحت تنش یکنواخت و تحت جابه جایی یکنواخت، اثبات می شود.}, keywords_fa = {روش المان مرزی,ضریب ترم آزاد cij,معادلات انتگرال مرزی,انتگرال منفرد}, url = {http://mcej.modares.ac.ir/article-16-1657-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-1657-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Goddossi1, parviz and sherzadi, ali}, title = {Effect of Restraint in Plastic Shrinkage and Settlement of Repair Materials Based on Self-consolidating Concrete}, abstract ={Plastic shrinkage occurs in fresh concrete within few hours after mixing the concrete. When the plastic concrete is allowed to shrink freely, it never cracks. But, generally, removal of unsound material or damaged concrete is a part of repair operation. Thus usually the surface of the substrate is rough, the repair concrete will be under restrained condition, which will result in the development of tensile stresses in the plastic concrete and will create cracks on the surface of the concrete. Four types of repair materials were used in this work: plane selfconsolidating concrete (SSC), SCC containing silica fume (S.F.), SCC containing S.F. and latex (Styrene Butadiene Rubber), and SCC containing S.F., latex and fiber. To roughen the surface of the substrate base, dents with different degree, referring to restraint indices, RI, were used to provide restraints. RI is defined as the ratio of the surface area dents to smooth surface area of the slab. The panels were subjected to sever combination of wind, temperature and relative humidity. The test program includes: settlement strains, free and restrained shrinkage strains, evaporation and bleeding rates, and cracks characteristic measurements. The results showed that, while the rate of evaporation and bleeding affected the shrinkage properties, it was over shadowed by properties of the repair materials and restraints indices. The results also indicated that, for a given repair concrete, the restrained strain increased as the R.I. increased. A significant improve was observed for the SCC with latex and fiber, exhibiting the lowest plastic settlement, shrinkage strains and crack area, and the highest time to the first crack. The plane SCC exhibited almost two times of higher settlement and shrinkage strains than the SCC with latex and fiber, for a given R}, Keywords = {Plastic settlement strains,Plastic shrinkage,Rate of bleeding,Restrained strains}, volume = {10}, Number = {4}, pages = {25-32}, publisher = {Tarbiat Modares University}, title_fa = {تأثیر قید در جمع شدگی و نشست خمیری مصالح تعمیری بر پایه بتن خودمتراکم}, abstract_fa ={چکیده- جمع شدگی خمیری، در زمانی که بتن حالت خمیری دارد رخ می دهد. در این زمان اگر بتن آزادانه جمع شود ، ه یچ ترکی در آن به وجود نمی آید اما در تعمیر سازه های بتنی، سطح بتن پایه زبر است و به علت این زبری، بتن تعمی ری، تحت شر ایط مقید قرار دارد و به دلیل توسعه تنش کششی در بتن تعمیری، احتمال ترک خوردگی بتن بسیار زیاد است. در این تحقیق 4 نوع بتن حاوی میکروسیلیس و ،SS حاوی میکروسیلیس که ،S تعمیری ارزیابی می شود که عبارتند از بتن خودمتراکم ساده، که در این تحقیق نامیده شده اند. برای بررس ی زبری های متفاوت SSLF و حاوی میکروسیلیس، لاتکس و الیاف که SSL لاتکس استایرن بوتادین که روی سطح بتن پایه، شیارهایی با مقطع نیم دایره با درجات قید (شاخص قید) مختلف در هر دو جهت سطح ایجاد شده است . بتن تعمیری پس از ریخته شدن روی بتن پای ه درون اتاقک باد و گرما قرار گرفته است و جمع شدگی و نشست و پارامتر های ترک خوردگی اندازه گیری شده است. نتایج نشان می دهد. بتن حاوی الیاف و لاتکس، کم ترین مقدار نشست و جمع شدگی خمی ری را نشان می دهد. کم ترین مساحت ترک و بیش ترین زمان مشاهده اولین ترک مربوط به بتن نوع لاتکس است . هم چنین کرنش جمع شدگی و نشست بتن خودمتراکم ساده و بتن حاوی میکروسیلیس حدوداً دو برابر بتن حاوی لاتکس و الیاف است}, keywords_fa = {کرنش نشست خمیری,جمع شدگی خمیری,نرخ آب انداختگی,کرنش مقید}, url = {http://mcej.modares.ac.ir/article-16-4852-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4852-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {saffarzada, mahmod and hasanpoor, shahab and mamdohi, amiraz}, title = {Airport Ranking Based on the Efficiency and Level of Services Using AHP Method}, abstract ={Abstract: One of the main reasons of weakness in airport system management and capacity insufficiency of its various sections is the lack of detailed information or reliable assessments of services of those sections of the airport. Proper airport management requires a thorough understanding of the performance of the different components and the airport system, as a whole. In this paper, a model of airport assessment and ranking is proposed after identifying and classifying the factors influencing the efficiency and level of service of the various sections of an airport based on the results of previous researches and a survey to gather the opinion of the experts in this field. The importance of the above factors and their sub-factors is determined using Analytical Hierarchy Process and the data gathered from the experts. The results of this model can help to identify airport weaknesses and strengths per airport section, make possible a quantitative comparison of airports and their ranks and also may be applied to identify the potentials of the different sections of an airport system. The results indicated that the efficiency factors (76.7%) are about three times more important than the level of service factors (23.3%). Also the two most important factors are runways (26.11%) while taxiways (9.6%) and the least important ones are baby changing stations (0.1%) and vending machines (0.11%).}, Keywords = {Airport,efficiency,Facilities,Level of services,AHP}, volume = {10}, Number = {4}, pages = {33-46}, publisher = {Tarbiat Modares University}, title_fa = {رتبه بندی فرودگاه ها بر اساس کارایی و AHP سطوح ارائه خدمات با استفاده از روش}, abstract_fa ={چکیده- یکی از دلایل اصلی ضعف در سیستم مدیریت فرودگاهی و نبود کفایت ظرفیت برخی از بخش ها ی فرودگاه، نبود اطلاع کافی یا ارزیابی دقیق، از میزان خدمت دهی آن قسمت فرودگاه است. برای مدیریت صحیح فرودگاه، باید از عملکرد و سیستم کلی اجزای آن آگاهی پیدا کرد. در این مقاله، پس از شناسایی عوامل مؤثر بر کارایی و سطوح ارائه خدمات فرودگاه ها ، روش ارزیابی و رتبه بندی فرودگاه ها بر اساس این عوامل ارائه می شود. هدف اصلی این مقاله، شناسایی و دسته بندی عوامل مؤثر بر کارایی و سطوح ارائه خدمات با استفاده از نتایج تحقیقات پیشین و مطالعات میدانی برای گرداوری نظرات خبرگان و کارشناسان است . میزان اهمیت هر یک از عوامل و پارامتر های زیرمجموعه آن ها، با پیاده سازی فرایند تحلیل سلسله مراتبی روی نظرات خبرگان حاصل از پرسشنامه، تعیین می شود. نتایج مدل رتبه بندی فرودگاه ها بر اساس کارایی و سطوح ارائه خدمات، سبب آگاهی از نقاط قوت و ضعف فرودگاه در تمامی بخش ها، اطلاع از رتبه هر فرودگاه نسبت به سایرین و شناسایی پتانسیل های مجموعه در هر بخش می شود. نتایج نشان می دهد که اهمیت عوامل مؤثر بر کارایی ( 76.7 درصد) حدود 3 برابر اهمیت سطوح خدمات ( 23.3 درصد ) است. هم چنین مهم ترین پارامترها، باندهای پرواز با 26.11 و باندهای خزش با 9.6 درصد و کم اهمیت ترین پارامترها، فضای نگه داری اطفال با 0.1 و دستگاه های خودکار با 0.11 درصد شناخته شدند.}, keywords_fa = {(AHP) کلیدواژگان: فرودگاه,کارایی,تسهیلات,سطوح ارائه خدمات,روش تحلیل سلسله مراتبی}, url = {http://mcej.modares.ac.ir/article-16-4512-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-4512-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {khodadady, ahmad and Ganjidoust, hosan and BaniMostafa3, ez}, title = {Cyanide Removal From Contaminated Sediment of Tailing Dam by Electrokinetic Technology}, abstract ={There are known techniques for cyanide remediation from contaminated soil such as soil washing, soil oxidation and biological degradation. However, there is very little research for electrokinetic remediation of cyanide from soil. This study investigates the application of electrokinetic remediation to contaminated soil with high clay content and low coefficient of permeability. The experiments were conducted with two electrodes as cathode and anode poles, which were placed inside the soil using the direct electrical current. Thus cyanide ions were transported to the anode pole and caused the remediation of the soil. The contaminated soil from tailing dam of Takab gold processing plant was used. Contaminated soil with the concentration of 420 mg/kg, distilled water and NaOH were employed in the electrokinetic cell. The experiments were conducted on the optimum moisture content of clayed soil at two voltage gradients (1.0 and 1.5 VDC/cm for the duration of 7 and 14 days) in order to assess the effect of voltage gradient when employing 1M NaOH solutions and distilled water at the anode pole. For each test, cyanide removal efficiency, the pH of the soil, moisture content, electrical conductivity and the electrical current and flow were determined. The measurements were conducted for the entire duration of electrokinetic experiments and at the end of the test. The results indicated that the cyanide removal obtained in 7 and 14 days was approximately 65% and 80%, respectively. The results also showed the pH of the soil was changed from 8.83 to 1-2 for the anode and to 12-13 for the cathode pole. The cyanide transported to the cathode and the pH were the most important dominant factors for cyanide remediation.}, Keywords = {Electrokinetic remediation,Contaminated soils,Cyanide,Tailing dam,Gold mine}, volume = {10}, Number = {4}, pages = {47-55}, publisher = {Tarbiat Modares University}, title_fa = {حذف سیانید از رسوب های سد باطله به وسیله فناوری الکتروکینتیک}, abstract_fa ={چکیده- پاکسازی خاک آلوده به سیانید با روش ها ی مختلف از جمله اکسیداسیون،خاکشویی، تجزیه بیولوژیکی و روش الکتروکینتیک انجام می شود. استفاده از روش الکتروکینتیک برای حذف سیانید تاکنون کم تر استفاده شده است. بنابراین، ای ن تحقیق برای بررسی کارایی این روش در خاک با درصد رس بالا و نفوذپذیزی پایین انجام شد . در روش الکتروکینتیک با قرار دادن دو که تحت یک میدان الکتریکی قرار گرفته است به سمت قطب مثبت (آند ) CN– الکترود داخل خاک و برقراری جریان مستقیم، یون با غلظت (CL) مهاجرت کرده و خاک پالایش می شود. در این پژوهش، پاکسازی خاک سد باطله معدن طلای تکاب از نوع رس سیانید 420 میلی گرم بر خاک خشک با استفاده از محلول های آب مقطر و سود 1 مولار در آند، مورد بررسی قرار گرفت. مایع مورد 1/5 با زمان V/cm 1 و V/cm استفاده در کاتد آب مقطر بود. خاک مورد نظر با رطوبت بهینه با استفاده از جریان مستقیم با شیب ولتاژ خاک،رطوبت، جریان الکترواسمز pH ، عبور جریان به مدت 7 و 14 روز آزمایش شد. در انتهای دوره، راندمان حذف سیانید از خاک و آمپراژ روزانه اندازه گیری شد. نتایج این تحقیق نشان می دهد که سیانید در مدت 7 و 14 روز به ترتیب با راندمان 65 و 80 درصد 8) به 1 تا 2 در نزدیک اند و 12 تا 13 در مجاورت کاتد تغییر کرد. تحلیل نتایج / خاک از میزان اولیه (حدود 83 pH. حذف شده است عوامل اصلی در تعیین راندمان حذف سیانید است. ،pH نشان داد که مهاجرت سیانید به سمت قطب مثبت (آند) و تغییرات کلیدواژگان: سیانید،}, keywords_fa = {الکتروکینتیک,سیانید,پالایش خاک,سد باطله}, url = {http://mcej.modares.ac.ir/article-16-11015-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-11015-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {Lotfollahi-Yaghin, m.a and Negin, m.}, title = {Effect of Random Initial Crookedness of Members on Reliability of Steel Frames}, abstract ={Abstract: The effect of two types of common initial geometric imperfections on the reliability of steel frames was investigated. These imperfections are the coordinates of connection nodes and crookedness of members. Most of the finite element reliability analyses in the past haveneglect this source of uncertainty. For this purpose, static non-linear pushover structural analysis was used in the present work from which reliabilities were estimated based on the FORM and Monte Carlo sampling methods. Furthermore, to investigate the importance of uncertain parameters, reliability sensitivity analysis was performed by the use of direct differentiation method, which was implemented in the object oriented framework of OpenSees software. It was demonstrated that some of these geometric imperfections have significant influence on the reliability assessment of steel frames.}, Keywords = {Steel Frames,Geometric imperfections,Reliability,Sensitivity,OpenSees}, volume = {10}, Number = {4}, pages = {57-69}, publisher = {Tarbiat Modares University}, title_fa = {مطالعه اثر انحنای اولیه تصادفی اعضا بر قابلیت اعتماد قاب های فولادی}, abstract_fa ={چکیده- در این مقاله دو نوع اثر ناکاملی هندسی اولیه در قاب های فولادی بر ظرفیت باربری و قابلیت اعتماد این سیستم ها مطالعه شده است. ناکاملی هندسی موجود در مختصات گره های اتصالی اعضای سازه به یک دیگر و ناکاملی هندسی ناشی از وجود انحنا در راستای اولیه و تئوری اعضای مختلف سازه که در مطالعات گذشته کم تر به صورت متغیرهایی تصادفی در تحلیل ها وارد شده است. به این منظور با انجام تحلیل استاتیکی و غیرخطی پوش اُور و با استفاده از روش ها ی مرتبه ی اول قابلیت اعتماد و شبیه سازی مونت کارلو، قابلیت اعتماد سیستم های مورد نظر محاسبه می شود. علاوه بر این، با به کارگیری تحلیل حساسیت به روش پیاده سازی شده، اهمیت هر یک از متغیرهای تصادفی مذکور از نظر OpenSees مشتق گیری مستقیم که در ساختار شیءگرای نرم افزار میزان تأثیری که در رفتار سیستم دارند ارزیابی می شود. نتایج به دست آمده نشان می دهند که برخی از ناکاملی های هندسی مذکور از اهمیت ویژه ای در قابلیت اعتماد این سیستم ها برخوردارند که نشان دهنده اهمیت تغییرات هرچند کوچک این پارامترها در احتمال خرابی قاب های فولادی است}, keywords_fa = {قاب های فولادی,ناکاملی های هندسی,قابلیت اعتماد,حساسیت,نرم افزارopensees}, url = {http://mcej.modares.ac.ir/article-16-6754-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-6754-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} } @article{ author = {nili, mahmod and Salehi, amir}, title = {Strength Development and Absorption of High Strength Concertes Incorporating Natural Pozzolan, Fly Ash and Silica Fume}, abstract ={Abstract: The effects of natural pozzolan, fly ash and silica fume as cementitious materials on strength development and absorption water capacity were investigated. Cubic specimens (100×100×100 mm) from 13 mix designs with 2 water-cement ratios of 0.3 and 0.46 were made. The specimens at the age of 28 days were dried and then immersed in water from 30 minutes to 7 days based on BS 1881, part 122, to study their cavity volume. The cement type 2 was replaced (by weight) with natural pozzolan and fly ash with 15, 30, 15 and 25 percent, respectively. Furthermore, in 0.3 water cement ratio specimens, the cement was replaced with silica fume at three percentages of 5, 8 and 11. It was concluded that natural pozzolan caused the decrease of compressive strength at both the early and later ages. Fly ash also caused the decrease of compressive strength at the early age, however, at the later age, it improved the compressive strength. Silica fume improved the compressive strength from the second day to the later ages. In 0.46 water cement ratio specimens, the absorption water capacity was decreased when the cement replacement with natural pozzolan and fly ash was 15%. Silica fume decreased the absorption water content when the immersion time was 7 days. In 0.3 water cement ratio specimens, the pozzolan materials had no considerable effect on the absorption water capacity.}, Keywords = {High strength concrete,Early age strength,Pozzolan,Absorption water capacity}, volume = {10}, Number = {4}, pages = {71-82}, publisher = {Tarbiat Modares University}, title_fa = {تأثیر پوزولان طبیعی، خاکستر بادی و میکروسیلیس بر روند کسب مقاومت فشاری و جذب آب حجمی در بتن های دارای مقاومت بالا}, abstract_fa ={چکیده- موضوع تحقیق حاضر، بررسی اثر جایگزینی پوزولان طبیعی، خاکستر بادی و میکروسیلیس با درصدی از وزن سیمان بر 0/ روی مقاومت فشاری و حجم منافذ داخلی بتن با مقاومت زیاد است. بدین منظور 13 طرح اختلاط با دو نسبت آب به سیمان 46 0 ساخته شد. در هر دو نسبت آب به سیمان، علاوه بر طرح شاهد، جایگزینی پوزولان طبیعی به مقدار 15 و 30 درصد و / و 3 0 و / جایگزینی خاکستر بادی به میزان 15 و 25 درصد وزنی سیمان انجام شد. میکروسیلیس نیز تنها در بتن با نسبت آب به سیمان 3 8 و 11 درصد جایگزین شد. نتایج به دست آمده نشان می دهد که جایگزینی پوزولان طبیعی باعث کاهش مقاومت در ، به میزان 5 سنین اولیه و نهایی می شود اما خاکستر بادی، با وجود کاهش مقاومت اولیه بتن، مقاومت فشاری دراز مدت بیش تری نسبت به نمونه شاهد دارد. هم چنین تأثیر عمده میکروسیلیس بر مقاومت فشاری بتن بعد از سن 2 روز آغاز می شود. حجم منافذ بتن با رده مقاومت پایین تر، با جایگزینی پوزولان ها کاهش می یابد. در حالی که پوزولان ها در بتن با مقاومت بیش تر ، تا سن 28 روز، تأثیر قابل ملاحظه ای بر منافذ بتن ندارند.}, keywords_fa = {بتن با مقاومت زیاد,پوزولان,مقاومت فشاری اولیه,مقاومت فشاری دراز مدت,جذب آب}, url = {http://mcej.modares.ac.ir/article-16-5350-en.html}, eprint = {http://mcej.modares.ac.ir/article-16-5350-en.pdf}, journal = {Modares Civil Engineering journal}, issn = {}, eissn = {2476-6763}, year = {2010} }