Volume 19, Issue 4 (2019)                   MCEJ 2019, 19(4): 145-159 | Back to browse issues page

XML Persian Abstract Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

karimi E, Kalatjari V R. Investigating The Effect of Cold-Joint on Seismic Behavior of Reinforced Concrete Moment Resisting Frame. MCEJ 2019; 19 (4) :145-159
URL: http://mcej.modares.ac.ir/article-16-30395-en.html
1- Ph.D. Candidate, Department of Civil Engineering, Shahrood University of Technology, Shahrood, Iran , eh.karimi@yahoo.com
2- Associate Professor, Department of Civil Engineering, Shahrood University of Technology, Shahrood, Iran
Abstract:   (5442 Views)
One of the common issues in the cast-in-situ reinforced concrete structures is creating a construction joint (cold joint) caused by an interruption or delay in the concreting operations. According to ACI 224.3R-95, construction joints in columns are to be provided below the beam for lower story columns and above the floor slab for upper story columns. The cold joint is a weakness or defect in the concrete, which results in the non-integrity of the concrete. For this reason, the performance of concrete elements with the cold-joint is under the influence of that behavior. The seismic design procedure for in-situ construction generally considers that the connection of beam and column that frames into the joint is monolithic in nature. But in actual construction, it is not possible to cast columns of the multi-story frame in one go and therefore, a cold joint is inevitable in all the upper story columns immediately above the lower story slab. In this research, firstly, cold joint behavior is modeled. The model of concrete damage plasticity used for the modeling the concrete behavior and the surface-based cohesive behavior with the traction-separation response used for the modeling the cold-joint. The three-point bending beam specimens with the same compressive strengths of concrete on both sides of the cold-joint have been used to verify the opening mode behavior of the cold joint from the experimental results. Three different sizes of the beam were considered to ensure the validation of opening mode behavior for the cold joint. So, the push-off test specimens have been used to verify the shear-friction behavior of the cold joint from the experimental results. Three same specimens with same compressive strengths of concrete on both sides of the cold-joint and the different number of steel connectors crossing the interface surface of the push-off specimens were considered to ensure the validation of shear-friction behavior for the cold joint. Then, a single-story single-bay reinforced concrete frame is modeled. After ensuring the validity of the numerical model of the cold joint and frame, a reinforced concrete frame containing a cold joint is modeled on its columns at the below of the beam and the top of the foundation. Subsequently, in order to investigate seismic behavior, an In-plane monotonic loading, stroke-controlled pushover tests were performed once on a frame containing a cold joint and once again on the same frame but without a cold joint. From the result, prior to the yield point, there was no difference between the load-displacement curve of the monolithic frame and frame with cold joints. In the range between the yield point and the failure point in the frame, a relatively small difference was observed between the load-displacement curve of the monolithic frame and frame with cold joints. A significant effect on the frame behavior was achieved in monolithic frame and frame with cold joints in their ultimate displacement so that the ultimate displacement in the cold-joint state was reduced by about 30% compared to the monolithic one. In fact, the finding results showed that under monotonic loading, the existence of a cold joint hadn’t any effect on the maximum lateral force of the frame, but reduced the ductility of it by about 30%.
Full-Text [PDF 1458 kb]   (2329 Downloads)    
Article Type: Original Research | Subject: Civil and Structural Engineering
Received: 2019/02/13 | Accepted: 2019/07/9 | Published: 2019/11/1

Add your comments about this article : Your username or Email:
CAPTCHA

Send email to the article author


Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.